You are here

Home

Nodes

Your search for "30" gave back 615 results.
Results for Forum Topic

Ubiquiti Litebeam 5AC Gen2 OS downgrade not working

published by HB9XCL on Mon, 06/12/2023 - 15:42
Forums: 
Nodes
Hi there, my new Ubuiquiti Litebeam 5AC Gen2 denies to be downgraded to OS v8.7.0 as described in the manual. It run on 8.7.11 build 46972 -> if I try to upload v8.7.0 I get an error saying "incorrect firmware version. Please upload v8.7.4 or newer". Now I've downgraded to v8.7.4 but still no luck to install v8.7.0 now. Any suggestions?

Ubiquity Powerbeam 500 gen2 unsupportet?

published by DF2TH on Sun, 07/02/2023 - 09:47
Forums: 
Nodes
Hello Everybody,
i got two PowerBeam AC GEN2 M/N:PBE-5AC-ISO-Gen2 Nodes.

The AREDN firmware installation fails. I get the message that it is an unsupported device. Both with version v3.23.4.0 and with Nightly Build 2023_06_06. Do I have the wrong firmware or is the hardware not yet supported?

73 Thomas
 

mesh RF address clash

published by nc8q on Fri, 07/07/2023 - 10:34
Forums: 
Nodes

I have a Mikrotik hAP and a GL-iNet AR750 that have a 'mesh RF address' clash.
These devices do not play well when on the same network.
How can I get them both to work on the same network at the same time?
hap image http://gelm.net/AREDN/hap2-32340.png
ar750 image http://gelm.net/AREDN/ar750-32340.png

73, Chuck

 

Mikrotik LHG5AC XL new install procedure failure

published by km6fq on Tue, 07/18/2023 - 15:20
Forums: 
Nodes

The ARDEN procedure to new install on a Mikrotik LHG5AC XL with v6.48.6 firmware requires downgrading to v4.45.8. The linked OpenWRT downgrade procedure states that OpenWRT newer than v6.46 must be downgraded to v4.45.8. The procedure provided does not work because on reboot the log file states that v6.45.8 cannot be installed because it is newer than the "factory version of v6.48.6". I upgraded to v6.48.7 to verify the procedure works when newer than v6.48.6. Mikrotik states that downgrading below the factory version is blocked because the hardware doesn't support it.

TP-Link CPE210 setup issue

published by K8HMF on Thu, 06/01/2023 - 15:06
Forums: 
Nodes

I just purchased two CPE210 nodes from Amazon and proceeded to set them up via the Pharos software. All went well until the AREDN install rebooted. Now I cannot connect to either node using the 192.168.1.1 ip. I can ping it and get 100 percent return. I am using a HP Pavilion g6 laptop running Windows 10. I cannot reach the node using MS Edge so I loaded Chrome and now I seem to reach the node but it will not allow connection. Any help would be most appreciated. TNX es 73, Dave K8HMF

Mikrotik LHG 5 won't keep config

published by W4SJN on Sun, 05/28/2023 - 18:28
Forums: 
Nodes
I’m trying to upgrade a Mikrotik LHG 5 firmware to AREDN.  I set the System / RouterBoard Boot Device to Try-Ethernet-Once-Then-Nand.  Protected Routerboot is unchecked.  I go through the process of upgrading with TinyPXE and reboot.  Once the device reboots it still has the Mikrotik firmware.  The IP is still 192.168.88.1.  Boot Device is back to Nand-If-fail-then-ethernet.

If I set the LHG back to Try-Ethernet-Once-Then-Nand, apply the change and just reboot it goes back to nand-if -fail-then-ethernet.  Any ideas?
 

Trouble with Nanostation M5-XW and SW 3.22.12.0

published by dm4ab on Fri, 03/10/2023 - 18:04
Forums: 
Nodes

Dear maintainers.

First of all, very good work you're doing with the project and the forum. Lots of information and good advice in here, and very good reading material as well. Especially for me as a newbie to AREDN, there is a lot to learn and study.

TPlink CPE210 with inoperable 3.23.4.0 won't boot replacement FW

published by kf7yrs on Tue, 07/25/2023 - 12:00
Forums: 
Nodes

I have 2 TPlink CPE210s V3.26 that I want to flash with AREDN firmware.  I first tried the most recent "aredn-3.23.4.0-ath79-generic-tplink_cpe210-v3-squashfs-factory" using the PHAROS software that came with the CPE210.  It flashed, I could ping it and open the NOCALL page.  When I entered the user/password I got the "Bad Gateway error that many have reported.   I just spent a week trying to reflash it with 3.22.12.0, which worked on my 2nd CPE210, using the TFTP and TinyPXE methods but nothing ever took.   Following the instructions on the bottom of this page

Mikrotik hap ac lite RB952Ui-5ac2nD-US

published by W4JWC on Sat, 08/12/2023 - 16:11
Forums: 
Nodes
I am about to setup my first AREDN Mikrotik node. I have watched several videos on the install.  I downloaded the factory and sysupgrade files.  The videos shows the initramfs-kernel file to have an .ELF extension but the newest (3.23.4.0) download has a .BIN extension.
The videos say to rename the file to RB.ELF should I change the .BIN extension to .ELF or should I rename the file to RB.BIN?
TIA

MikroTik SXT routerboard boot settings/Won't sysupgrade

published by kf0dyw on Mon, 02/20/2023 - 13:08
Forums: 
Nodes

Does anybody know the correct settings for the boot settings on the MikroTik SXT?  I believe the options are a mix of nand, flash, dhcp, and bootp.  I'm stuck in endless DHCP boot sequence after first applying the correct .elf file and I get to the NOCALL first boot just fine, but I can't seem to apply the sysupgrade .bin file and make it through that next boot sequence.   

Are there log  trails or syslog setup that I can look at?

Pages

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer