You are here

Home

Nodes

Your search for "30" gave back 616 results.
Results for Forum Topic

AC Equipment

published by W7BJH on Wed, 12/28/2022 - 02:04
Forums: 
Nodes
Any chance there is some firmware under development for the AC 2.4 and 5 GHz Ubiquiti equipment?  I've got an NBE-5AC-16 on-hand that I'd like to put to work and there is actually some AC gear in stock.

Cheers, 

BJ - W7BJH

Nightly for NanoBridge 5G25?

published by KE6GYD on Tue, 01/10/2023 - 22:51
Forums: 
Nodes
I know the nightlys' now are using OpenWRT release, version 22.03.2 and that some older 32MB Ram devices like the NanoBridge 5G25 are being sunsetted.
Has the sun set on these devices yet?  Or does this OpenWRT release, version 22.03.2 nightly still work on these devices but has not been tested?

If the nightly will still work, I'd like to try it on my NanoBridge, but don't know what nightly file to use.  If sunsetted, then I'll just continue to use the last stable release.

Thanks
Bob
KE6GYD
 

TP-Link CPE610v2 problem

published by LU4EOU on Tue, 01/10/2023 - 10:41
Forums: 
Nodes

Hello.
I have 1 tplink node cpe610-v2 updated until 3.22.12.0 all ok, updated with NB 2024 ok, then 2065 ok, then to 2074 ok, 2081 ok, to 2089 ok, to 2096 ok, to 2103 ok, then I could not update more, try with 2110, with 2124 and with 2131 and the same error.

Firmware CANNOT be updated
firmware file is not valid: platform check image failed

Any ideas that will help me?

Thanks
Mario, LU4EOU

Attached file

CPE510: Separate WAN and LAN port

published by db9cr on Sat, 01/21/2023 - 12:08
Forums: 
Nodes
Hello,
just installed my first AREDN node on a CPE510.
I got LAN on both ethernet interfaces untagged (and as I understand the documentation, didn't test, WAN on both interfaces tagged as VLAN 1).
Is there a way to get LAN untagged on one of the interfaces and WAN untagged on the other?
Thanks in advance.
73 Christian DB9CR
 

Unable to flash firmware GL-AR750S

published by KJ7CLT on Mon, 01/23/2023 - 23:08
Forums: 
Nodes
I am looking into connecting and I have unsuccessfully tried to flash GL-iNet GL-AR750S-EXT. I used the GL-AR750 sysupgrade but it only ends up continuously rebooting and I can't get a stable IP from it. I was able to reload GL firmware and backup, so it didn't fully brick. Is the GL-750 not compatible?
https://www.gl-inet.com/products/gl-ar750s/ is what I have.
https://www.gl-inet.com/products/gl-ar750/ is the generic. 

Getting disconnected when updating settings

published by VE7NZ on Tue, 01/31/2023 - 19:52
Forums: 
Nodes
I have flashed and updated a Basebox 5.  But when I try to make changes to things like the channel number, call sign, etc in the Setup menu, as soon as i hit "Save" I get a 404 like error where the browser says "This Site Can't Be Reached.  Connection Reset" - i am disconnected from the Basebox.  I am using DHCP with a laptop connected to the Basebox 5, nothing else is involved.  I can then go to local node.local.mesh (roughly correct syntax going from memory) but any attempt to save a change doesn't work and I get booted out.

Limiting WAN access

published by VE7NZ on Tue, 01/31/2023 - 19:47
Forums: 
Nodes
I have setup a test link between two nodes in my basement and as an experiment was able to provide access to the web via one of the node's WAN ports on a Microtik ac HAP lite.  My concern is that if I set this up on the mesh then perhaps it presents an open WAN channel to all nodes which could be an issue regulatory and bandwidth wise.

Is there a way to limit such a WAN gateway so that only a specific remote node can use the feature?

Thx Adrian VE7NZ

MikroTik-LHG-XL Models

published by KM6ZJT on Fri, 02/03/2023 - 22:18
Forums: 
Nodes
I'm interested in getting a dish type node to connect to a hilltop about 4 miles away from me.

Looking at AREDN's Support Platform Matrix, I see that the MikroTik RBLHG-5HPnD-XL is supported.
Link: https://mikrotik.com/product/RBLHG-5HPnD-XL

Shopping online, I also see a MikroTik product called the RBLHGG-5acD-XL.
Link:https://mikrotik.com/product/lhg_xl_5_ac

Some of the differences are listed below:

Rocket M2 v6.0.7 Downgrade Issues

published by KC2LPD on Tue, 06/19/2018 - 17:36
Forums: 
Nodes
Hello,

I currently have a UBNT Rocket M2 running AirOS v6.0.7 and have not been successful in getting it downgraded to a firmware version that supports AREDN.  I even tried the 6.0.6 beta firmware, but the Rocket will not accept this as it is v6.0.7.  Does anyone have a firmware path that will enable the device to downgrade? Thanks

73,
Jacob

Missing 'MAC2' on Meraki MR-16

published by VE6CWB on Fri, 02/17/2023 - 20:23
Forums: 
Nodes

I installed AREDN (aredn-3.22.12.0-ar71xx-generic-mr16-squashfs-sysupgrade.bin) on a Meraki MR-16. (Yay!) I did install an older version of OpenWRT 19.07.5 first, as indicated in the instructions I followed, and I did set the Mac address.

On my first boot, when I enter in some basic information and try to save it, I get the following message:
 

Pages

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer