You are here

Home

Hardware

Your search for "28" gave back 1102 results.
Results for Forum Topic

TP Link CPE710 setup problems

published by K8HMF on Tue, 06/27/2023 - 14:25
Forums: 
Nodes
I am trying to get a demo AREDN network setup here in Central Florida. I had hoped to get this operational for demo on Field day. I setup a system about five years ago but couldn't get much interest going. I didn't have any big problems in flashing the nodes and had  IP phone and HD PTZ camera links. I have been struggling for the past month in getting nodes to flash. I was able to get a pair of TP Link CPE210 nodes flashed via the PHAROS application. I have tried this on the CPE710 but it gives an unsupportred hardware error. I have also tried PXE but it doesn't load the BIN file.

MicroTek Basebox - Bad Gateway error

published by K1DOS on Mon, 11/06/2023 - 18:51
Forums: 
Nodes
I have a basebox and cannot get it updated.   I am not sure what file I should use from the nightly builds.  I keep getting a bad gateway error.  any help would be appreciated.  I have attached a pdf of the current firmware loaded in the node.

 

MikroTik Tutorial

published by AJ6GZ on Sat, 03/10/2018 - 17:21
Forums: 
Network Switches

Mikrotik has a huge variety of routers, wifi devices, and circuit boards (“RouterBOARDs”) which all run their RouterOS. They also have some switches running SwitchOS. We will concentrate on the Routers as they are most flexible for what we are doing. Below is guide on configuring these devices to support AREDN nodes and hosts, Pi, phones, cameras, etc.

dtdlink in status display

published by WA3LAB on Tue, 08/29/2023 - 16:42
Forums: 
Nodes

​I have a CPE710 node programmed with the latest 23.8.0 firmware.  The node connects to my Powerbeam 5GHz via RF and it is also connected via DTD.  The mesh status shows as shown below. (dtdlink.WA3LAB.CPE710/WA3LAB.local.mesh)  According to the documentation, this is some type of issue with OLSR, and I tried the fix several times, but this status persists.  The node appears to be functional.  Does this status mean it is connected DTD and RF?  
Glenn WA3LAB




Sysupgrade fails during first install on hAP ac lite

published by DF2SI on Tue, 04/02/2024 - 05:30
Forums: 
Nodes
I have a mysterious problem when performing a first install on an hAP ac lite which never happened to me before, although I have successfully installed AREDN sw on a number of Mikrotik devices.

PowerBeam-M2-400 Firmware?

published by AK4ZX on Wed, 04/10/2024 - 16:24
Forums: 
Nodes
I have a Ubiquiti PowerBeam-M2-400.  However, when I visit the downloads page (https://www.arednmesh.org/content/current-software) and search for it, all I see is "no model found".

The list of firmware though shows it here:  http://downloads.arednmesh.org/firmware/html/SUPPORTED_DEVICES.md

PowerBeam-M2-400

If I search on PowerBeam, only the XW version shows.

No WAN on GL-AR300M16-ext

published by AA6BD on Wed, 04/24/2024 - 16:07
Forums: 
Nodes
I have a GL-AR300M16-ext node where I loaded the AREDN firmware V3.23.4.0 some months ago and it was working fine.through a tunnel.

Gl.iNet GL-AR300M Nand

published by K4JLN on Sun, 04/14/2024 - 21:21
Forums: 
Nodes
I got this little router, and I've followed the steps to upgrade the firmware, per the First Install Instructions in the document. When I get to the "Upgrade Firmware Local" in the advanced settings area, I choose the file, and the device comes back and says it's an invalid image file. I've used the sys-upgrade.bin file from the currently nightly build, the 3.23.4.0 build, and I tried the 3.22.12.0 build. And it always comes back saying it's an invalid image file. Any suggestions, to get this onto the AREDN build?

Thanks
Jim, K4JLN

MikroTik hAP AC3 initial AREDN Loading

published by w8erw on Wed, 04/12/2023 - 03:31
Forums: 
Nodes
I've not seen anything specific to the new hardware regarding the Mikrotik hAP AC3 and the initial loading of AREDN firmware.
Would this follow the same process, changing the initial load firmware name, rb.elf?
I have one here new in the box and am cautiously contemplating the process to load with AREDN and wish to not mess it up..

Thanks,
Jim W8ERW
 

Is ath71 support deprecated

published by wv6u on Wed, 05/01/2024 - 13:47
Forums: 
Hardware
Hi All,

I checked the supported hardware matrix and decided to buy a pair of Ubiquiti Litebeam 5 (LBE-M5-23-US) since the matrix showed the hardware was supported (light green). But when I checked available firmware, I see that ath71 based hardware is only supported till 3.22.12. Going over OpenWRT forums, what I understand is that while ath71 targets can be ported to the latest OpenWRT (and Aredn) firmware but it requires work and that hasn't happened. 

Pages

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer