You are here

Home

Hardware

Your search for "28" gave back 1102 results.
Results for Forum Topic

Mikrotik hAP ac3 restore from AREDN back to factory OS

published by N6GKJ on Sun, 12/10/2023 - 18:44
Forums: 
Nodes
Hello Folks!

This was an exercise in futility. No matter what I do I cannot get the WAN port to talk to my home router. When looking at the WiFi Scan from another device, I see this ac3 with up to 6 channels, but the Host name is blank and I see Foreign Network.

I have decided to restore this to factory and send it back, I have not been able to find a document that explains how to do it... Anyone who has the document or can point me to it would be greatly appreciated if you could share that. I am very disappointed that I could not get this to work

GL.iNET GL-E750 Help!

published by AA3JC on Tue, 05/16/2023 - 11:02
Forums: 
Nodes

I need some directions on flashing this unit.  I searched on Aredn and could only find general info on other GL-iNet hardware.  I downloaded the system firmware, but when I try to download the factory 1st flash firmware, it takes me to a blank page!  Not sure if that was done on purpose as it is not needed, but after trying to upgrade the node via the upgrade tab using the system upgrade file, in the web based interface, it does complete the upload, the display changes to "upgrading" but gets stuck there and never goes any further for over an hour.  At this point if you try to connect via 1

HAP AC LITE VLAN CHANGE NEEDED

published by AA3JC on Sun, 12/10/2023 - 10:07
Forums: 
Network Switches
I need to make a change on my HAP AC LITE, from the standard VLAN configuration to allow LAN AND DTD traffic on port 5 that already supports DTD on this port 5. The purpose is that I have a 26 port smart switch that is configured for all my nodes with LAN ports configured for each node, 
simular to the Aredn Docs for the Netgear GS108E. I know my switch is configured correctly as when I plug a node (not the HAP) into a configure node port, the configured LAN ports all work as expected.
 

MicroTik hAPac Lite

published by N6GKJ on Wed, 12/13/2023 - 17:02
Forums: 
Nodes
Hello Guys!

I have converted 2 of the  hAPac Lite units and they seem to work. I get 54Mb/s on my link between the two of them. I am running 20MHz chan width.
is this normal for these units?

73,
Ron

MicroTik hAPac lite stopped sharing services

published by N6GKJ on Wed, 12/13/2023 - 22:51
Forums: 
Nodes
Guys, 

Running the latest nightly build for this device. Tunnel works solid, no drop outs. MY servcies work, if I namually go to them, but they are not displayed in mesh status. Is there a switch I missed? they used to be visible.

73, 
ROn

Ubiquiti NanoBridge Won't Flash

published by NA7RF on Tue, 12/12/2023 - 19:32
Forums: 
Nodes
I seem to get the problem nodes to work on in my local area.  I have a NanoBridge that is giving me troubles.  I don't know the history behind the node or if it is an XM or XW.  It does have writing on it suggesting that it was flashed at one time.  I don't even know for sure if it is a NanoBridge and pretty sure it is for 2Ghz.  I wish Ubiquiti put better marking on these devices.

Mikrotik cAP ac support

published by S50RP on Mon, 12/18/2023 - 11:27
Forums: 
Hardware

I have couple of Mikrotik cAP ac (RBcAPGi-5acD2nD). According to Mikrotk product page (https://mikrotik.com/product/cap_ac#fndtn-specifications) it uses 4 core 32-bit ARM (IPQ-4018), so i guess in the ballpark of hap ac/ac2/ac3. Any ideas why it's not supported or listed in http://downloads.arednmesh.org/firmware/html/SUPPORTED_DEVICES.md.

73 de S50RP

Mikrotik hAP ac3 ... is this junk??

published by N6GKJ on Sun, 12/10/2023 - 11:30
Forums: 
Nodes
Hello Folks!

Well I bought a hAP ac3 router, after some learning curve on getting it to accept the flash, it is finally operational.

I find however that this unit seems to be deaf.. I am operating on 2.4GHz at channel -2. I get 24 Mbps to the existing gateway which is a GL-AR300M16EXT device and 5.5 Mbps to a second GL-AR300M16EXT device. the two GL-AR devices talk at 72 Mbps between them.

Mikrotik Mislabeld Product

published by KL5T on Sun, 11/05/2023 - 22:47
Forums: 
Hardware

I recently ordered what was to have been a Mikrotik LHG XL 5 AC (RBLHGG-5acD-XL-US) from Amazon.  It was advertised as follows:

Pages

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer