You are here

Nodes

Your search for "30" gave back 615 results.
Results for Forum Topic

MicroTek Basebox - Bad Gateway error

Forums: 
I have a basebox and cannot get it updated.   I am not sure what file I should use from the nightly builds.  I keep getting a bad gateway error.  any help would be appreciated.  I have attached a pdf of the current firmware loaded in the node.

 

dtdlink in status display

Forums: 

​I have a CPE710 node programmed with the latest 23.8.0 firmware.  The node connects to my Powerbeam 5GHz via RF and it is also connected via DTD.  The mesh status shows as shown below. (dtdlink.WA3LAB.CPE710/WA3LAB.local.mesh)  According to the documentation, this is some type of issue with OLSR, and I tried the fix several times, but this status persists.  The node appears to be functional.  Does this status mean it is connected DTD and RF?  
Glenn WA3LAB




Sysupgrade fails during first install on hAP ac lite

Forums: 
I have a mysterious problem when performing a first install on an hAP ac lite which never happened to me before, although I have successfully installed AREDN sw on a number of Mikrotik devices.

PowerBeam-M2-400 Firmware?

Forums: 
I have a Ubiquiti PowerBeam-M2-400.  However, when I visit the downloads page (https://www.arednmesh.org/content/current-software) and search for it, all I see is "no model found".

The list of firmware though shows it here:  http://downloads.arednmesh.org/firmware/html/SUPPORTED_DEVICES.md

PowerBeam-M2-400

If I search on PowerBeam, only the XW version shows.

No WAN on GL-AR300M16-ext

Forums: 
I have a GL-AR300M16-ext node where I loaded the AREDN firmware V3.23.4.0 some months ago and it was working fine.through a tunnel.

Gl.iNet GL-AR300M Nand

Forums: 
I got this little router, and I've followed the steps to upgrade the firmware, per the First Install Instructions in the document. When I get to the "Upgrade Firmware Local" in the advanced settings area, I choose the file, and the device comes back and says it's an invalid image file. I've used the sys-upgrade.bin file from the currently nightly build, the 3.23.4.0 build, and I tried the 3.22.12.0 build. And it always comes back saying it's an invalid image file. Any suggestions, to get this onto the AREDN build?

Thanks
Jim, K4JLN

MikroTik hAP AC3 initial AREDN Loading

Forums: 
I've not seen anything specific to the new hardware regarding the Mikrotik hAP AC3 and the initial loading of AREDN firmware.
Would this follow the same process, changing the initial load firmware name, rb.elf?
I have one here new in the box and am cautiously contemplating the process to load with AREDN and wish to not mess it up..

Thanks,
Jim W8ERW
 

Mikrotik SXTsq 5 High Power gets stuck at boot up

Forums: 
Hi All,

I have a "RBSXTsq5HPnD-US" (interestingly, the "IC" value on the back says 7442A-LHG5HPND). I got the latest Aredn firmware flashed on it (3.24.4.0). Everything else seems to work fine on it except at bootup, it gets stuck as a DHCP client.

Ubiquity Lite Beam

Forums: 
Is this the Lite Beam listed on the Aredn Matrix as usable? https://www.amazon.com/LiteBeam-LBE-5AC-Gen2-Ethernet-Protector-High-Spe...
Thank you.
 

Ubiquiti AirMAX LiteBeam M5 23 dBi (LBE-M5-23)

Forums: 

Greetings folks!

I've looked through the available downloads and supported hardware, but nothing is listed for the LiteBeam.

Is this piece of hardware similar to any other?
Can it be used?
If so, which firmware should be flashed into it?

Thanks!
Matt
VE3OY
 

Pages

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer