You are here

Home

Nodes

Your search for "30" gave back 615 results.
Results for Forum Topic

GL-iNet B1300 Firmware rejected

published by M0GXB on Thu, 12/19/2024 - 10:22
Forums: 
Nodes
My GL-iNet B1300 (Convexa-B) works fine with the factory OpenWrt system, and behaved as per the documentation, but I cannot install AREDN because the firmware image is immediately rejected due to some kind of verification that it is doing*. Conveniently it reports the SHA of what it read which is exactly correct - so data corruption is not the reason.

So what am I supposed to do to make the firmware install?

Ubiquiti LiteBeam 5AC firmware installation challenge - SOLVED

published by KE6YOH on Tue, 10/22/2024 - 11:39
Forums: 
Nodes
Addendum:  I have been informed that some of the LBEs had different flash chips, something that will be addressed in a future version of the code. Since I sent my inaccessible LBE back via RMA and was sent a new unit in return, it is possible that I just got lucky this time around with the replacement's flash chip. All I would advise is that if you get to "step 3" in my original posting, where the wifi "mesh 2" network is the only option you have for accessing the unit.

Rocket R5AC no network?

published by kg7kmv on Tue, 01/21/2025 - 12:51
Forums: 
Nodes
I bought a used Rocket R5AC-lite. I got the firmware flashed in the typical fashion with no issues. However it now does not DtD link with other nodes!
I have these devices, all have current firmware 3.24.10.0
  • Mikrotik RB750UPr2 setup with a simple bridge on all ports. no filtering, NAT, vlan, nothing.
  • Mikrotik hAP Ac lite
  • GL.iNet GL-AR750
  • the Rocket R5AC-lite in question
 
  • The hAP and AR750 have DtD linked to each other, but neither one can "see" the R5AC. 

Aredn Node UI

published by N3DMC on Sat, 02/15/2025 - 09:02
Forums: 
Nodes
I have been working on the hAP ac3. The new update fixed dtd issues. Now I see the dish on local node list. I go to click on the device and get the UI - 

Hmm. We’re having trouble finding that site.

We can’t connect to the server at n5jlp-708-w-ave-o-tower.local.mesh.

If use a poe and connect it to the computer I can get in the node.

Whats the issue here? Its on port 5 dtd. We can access the allstar node on the other dish. I know the link is solid.

Dave
N3DMC

Mikrotik XL HP5 ethernet issue

published by AD6KV on Wed, 02/19/2025 - 17:59
Forums: 
Nodes
Recently upgraded to ver 25.x.x successfully, went into package management to remove and reinstall meshchat.  After rebooting no ethernet activity.  I'm unable to recover ethernet and the node.  Suggestions?

Mikrotik QRT5 911G-5HPnD support

published by AE6XE on Wed, 12/19/2018 - 00:23
Forums: 
Nodes

The Mikrotik QRT5 flat panel device will be available in the Dec 19, 2018 Nightly Build.    While it is a bit more cost than other devices with similar performance this 5GHz device has a very low profile and relatively small foot print.   In a 12" x 12.5" x 2" (max depth) packaging, this device commands:

xmit:   30dBm
gain:   24dBi

https://mikrotik.com/product/RB911G-5HPnD-QRT

Mikrotik OmniTIK U-5HnD

published by OK1VRA on Thu, 12/12/2024 - 17:21
Forums: 
Nodes
I would like to ask if it is possible to run AREDN firmware on a Mikrotik OmniTIK U-5HnD device, which is not on the list of supported devices?

Install issue

published by ke6abz on Mon, 11/11/2024 - 23:48
Forums: 
Nodes
I have two Ubiquiti NanoStation Loco M5 units.
Tried installing the first, seemed I bricked it.
Tried the second one and it went well, installed and tested, connected to the mesh.
Went back to the first one:
Put it in TFTP Server mode and PUT the Ubiquiti firmware on it and it works fine.
Put it in TFTP Server mode and PUT the AREDN firmware on it, It reboots and all, LEDs look like the functioning one but I cannot connect to it.
LEDs Power ON, LAN Blinking Next LED slow RED Blink, Last LED Green solid on.

GL.iNet GL-AR300M16-Ext Flash Change

published by AD5JK on Tue, 03/04/2025 - 15:11
Forums: 
Nodes
I was doing an initial install on a new AR300M16 today.  It appears there may be a new/different built-in firmware than what is described in the main AREDN Install Docs.

Mikrotik NetMetal 5

published by AK4ZX on Tue, 02/18/2025 - 15:20
Forums: 
Nodes
Hello All.

The Mikrotik NetMetal 5 is a new edition to the hardware available for AREDN.  Looking on Amazon, there are several variations of this though they all look the same visually.  Is the "US Version" the one to buy? 

Amazon List of NetMetal 5's

Thanks.

Gary
 

Pages

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer