Nodes

New install
Put unit in XCV 8.7.0 on dashboard
ip .20
pc ip.10
When I try to upload in step two I get error
with the local path command

scp \hold\upgrade25.bin ubnt@192.168.1.20:/tmp/factory.bin
When I tried the next example for unable to negotiate

scp -oHostKeyAlgorithms=+ssh-rsa -oPubkeyAcceptedAlgorithms=+ssh-rsa \hold\upgrade25.bin ubnt@192.168.1.20:/tmp/factory.bin

Still no luck getting to upload to device.


Any Ideas on my mistake?
73

I'm feeling a bit stupid.  I tried loading recent versions of AREDN onto an older nanostation, the version of which I couldn't determine; and onto an older nanobridge M5 that was acting like an M2.  In both cases  the only lights showing are the power light and the red light that only goes off and on.  I've tried the reset button on the nanostation without any effect.  I'm yet to try it on the M5.  Can anyone give me some guidance to get them both back up and running?

David Oswald, KD7DHO

I recently flashed my Mikrotik hAP ac lite. I am doing this on windows. I got all the way to creating the node (callsign-1). router rebooted but now I can't connect to the node. I reset my IPv4 address to obtain automatically. When trying to connect to http://localnode I get the error below:

hAP ac lite is not powering up via PoE-in port eth 1 tried SW port w/ poe, poe+, upoe ports. 

• New deployment, power adapter works fine.
• Multiple tests & fails on 3x hAP ac lites. (also tested w/ disable PoE-out, usb-out)
• model: MikroTik RouterBOARD 952Ui-5ac2nD (hAP ac lite) 
• Firmware: v 3.25.2.0

Hi, I've gotten pretty good at flashing Mikrotik nodes, perhaps 40+ with no failures until this last month.  That includes ~12 LHGs of various subtypes.   Recently, our local hospital brought me 6 LHG5nDs to flash (RouterOS 6.49.13) and the local club had 3 more (6.48.7).  5 of the hospital's went fine and 2 of the club's went fine.  One from each group refused to load the sys-upgrade file.  I loaded 20240926-5913b09 on the Club's (one failed) and 3.24.10.0 on the hospital's (one failed).   At first I used the "V7" files because they worked...until they didn't.  Then I tried perhaps 5 differen

I have a HAP AC lite that I have struggled to get flashed. I currently have AREDN installed with my settings, but I have to hold reset while applying power in order for it to boot. If I do not press reset then the HAP is stuck (forever) looking for a TFTP server.

I have flashed OpenWRT and I have the same experience. How do I overcome this issue? My guess is it has something to do with the various Mikrotik reset button modes, and maybe protected boot?

Am trying to flash Ubiquiti NanoBeam AC with AREDN firmware. Changed existing firmware to 8.7.0 and copy AREDN firmware to node and wrote the program to bypass checking process,but when I try to load the firmware from the Ubiquiti WA prompt, I get a group of error messages starting with error in line 1 and error in line 17. Had also tried logging out of Ubiquiti prompt and upgrading firmware direct from setup in node but upgrade fails due to not being signed.

Hello,
As this is my first post here I'd like to welcome everyone.

I’m trying to install AREDN firmware on a Mikrotik board and I am struggling with that. 

At the beginning I’d like to mention that I have some basic experience with that process - 3 running nodes - 2 of them Mikrotik. Thus the problem isn’t trivial.

Saw Ori post in Github that  hAP ac lite will no longer be recommended?!. even though it is still listed on hardware support?

https://github.com/aredn/aredn/issues/2074

Please advise as we got just recently bought a bunch of ac lite's and had multiple fail to upgrade on the last  two nightly builds and to re-flash.

• See posts about ac lite crashing and where memory is a starting to become an issue... how about if we disable wireless?

I flashed my ac lite with 3.25.2.0 and can create a mesh connection with my ac3, but when I plug the ac lite into my home router (using port 1 here from https://downloads.arednmesh.org/snapshots/readme.md and https://arednmesh.readthedocs.io/en/latest/arednHow-toGuides/home-router... ) the ac lite gets hot and turns both LEDs off, which made me worried about some electrical fault.