You are here

Home

Nodes

Your search for "30" gave back 615 results.
Results for Forum Topic

GL.iNet GL-MT3000 support

published by N2SGL on Wed, 04/24/2024 - 21:22
Forums: 
Nodes
I've been working on getting the GL-MT3000. It is supported in openWRT, but the wifi scan isn't finding other wifi on the 5ghz especially other nodes I have working on channel 165. Is anyone else working on getting the GL-MT3000 working with AREDN software ?

Ubiquiti PBE-5AC-Gen2 First Install Success

published by KL7KVG on Mon, 10/14/2024 - 17:12
Forums: 
Nodes
Over the weekend I acquired an Ubiquiti PowerBeam 5AC Gen2 (PBE-5AC-Gen2) device and successfully completed an initial install of the AREDN firmware following the "Ubiquiti 802.11ac First Install Process" instructions.  I was able to downgrade the installed Ubiquiti firmware to WA.V8.7.0.  The rest of the commands went off without a complaint.  It appears to be running normally on version 3.24.10.0 firmware.  The status screen reports the radio as an Ubiquiti PowerBeam 5AC 400 / Gen2.

Rocket M5 local lan expected behavior

published by KN0O on Mon, 11/27/2023 - 20:41
Forums: 
Nodes

I was able to flash a Rocket M5 and begin the setup process. When I have the Rocket connected to a dumb switch (through a POE injector) and my computer is connected to the same switch with DHCP turned on on the computer ethernet, the Rocket assigns an IP address to the computer and I can access the Rocket and setup page. 

LightBeam 5AC Gen2, install works

published by kn6pe on Tue, 07/23/2024 - 10:18
Forums: 
Nodes
Hello UI users,
This is an FYI...  My Ubiquiti LightBeam 5AC Gen2 arrived last week so yesterday (22-July-2024) was AREDN flash day.

My radio arrived with firmware V8.7.11 installed so an upgrade (or downgrade, in this case) was required.  On loading 8.7.0, i did get the error message stating it wanted at least 8.7.4 and uploaded that one instead... PASS!  The instructions flagged this so i was prepared.

Hap AC Lite issue DNS or IP ?

published by KD9NZK on Wed, 11/13/2024 - 10:18
Forums: 
Nodes
Hey all - new here.  

I've got a Hap AC Lite setup with WAN on my home network - so it has internet connection.  It's successfully tunneled to a friend site. 

I am trying to connect to it with a mini travel router - single WAN single LAN -- Lan connected to laptop - no WAN.  it's using the 2Ghz band, channel -2 10Mhz.
default settings.  

I can see the Hap just fine - but if I try to click on any services (meshchat) or any tunnel services from other sites - I get a page not found - err.

Ubiquiti Bullet AC

published by KI7NNP on Mon, 11/18/2024 - 23:03
Forums: 
Nodes
I'm flashing the Ubiquiti Bullet AC 3.24.10 and following the instructions it does come up but:
1) Switches from 192.168.1.20 to 192.168.1.1 and does DHCP service.
2) Only Telnet and ssh services running, no webservice.
3) The ash CLI is running and you can telnet or ssh in.

So sysupgrade to the nightly build, now web service works with the new UI but lots of stuff missing. I can change the node name, password, and location, but the usual "todo" list isn't there, just a blank yellow area. Most normal new UI stuff is missing.

Mikrotik Basebox Out of Date - Can't Update?

published by K1DOS on Sat, 11/30/2024 - 17:44
Forums: 
Nodes
I have an older Mikrotik basebox on a tower that has not been updated in awhile.

"Current Version: 3.22.12.0 Hardware Type: (ar71xx/mikrotik) mikrotik (rb-912uag-2hpnd)"

Can someone advise how I can advance this older load to get up to date?

Hank - K1DOS
 

More Proxmox VM fun

published by AH6LE on Sun, 12/01/2024 - 14:41
Forums: 
Nodes
Was not able to get 3.24.10.0 nor even 3.24.6.0 to work right so ended up installing nightly 20241128-d7754d89 and that seems to pretty much work but I did find an issue in that it will not save DHCP MAC reservations.

After selecting the leases I want to reserve, I click the DONE button and the popup closes. However I am never presented the usual COMMIT banner at the top either, the popup simply closes. When I reopen to check, the LAN DHCP popup is like I never selected any reservations.
 

Rocket Fails

published by w8erd on Sat, 12/21/2024 - 13:50
Forums: 
Nodes
My rocket has always worked. But suddenly I cannot connect to it from my PC.  The RF and is working as I can connect to it from other nodes.
Suggestions?

Bob W8ERD

Rocket 5AC Lite Stuck on NOCALL setup page

published by VE7KOD on Tue, 01/02/2024 - 23:55
Forums: 
Nodes

Have flashed the Factory image as per the Ubiquiti first flash set up and currently will not go past the NOCALL page (initial setup - change node name/password).

I can log in to the admin setup page and change the Node Name and Password but when it reboots, it goes back to the NOCALL page as if nothing was saved. I have tried everything that I can think of.. Changing from static to DHCP, unplugging the node, soft reseting the node, clearing browser cache, trying different browsers. 

Pages

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer