You are here

Home

Nodes

Your search for "30" gave back 615 results.
Results for Forum Topic

Update to v3.16.1.1 broke my AirRouter

published by w7rej on Tue, 10/17/2017 - 23:09
Forums: 
Nodes

So, as the subject says. I have an AirRouter I use at home with the Wan port that gets me on the internet. My PC is connected to the AirRouter via Ethernet Cable. The AirRouter was running v3.16.1.0.

iPerf (and iPerfSpeed)

published by w7rej on Fri, 10/20/2017 - 23:47
Forums: 
Nodes
I searched and didn't see anything regarding what I'm about to ask. Also, I'm really not sure if this should be posted here or to Deployment. I think here is probably more appropriate, anyway...

I've just updated a couple of my nodes to the latest firmware and in the process added iPerf and iPerfSpeed. When I ran iPerfSpeed between these two nodes in either direction, I get a "connection Refused" message. This is the first time I've run into this from lots of installs of iPerf and iPerfSpeed on dozens of nodes in our network.

M2 Rocket Upgrade Problem

published by AB4YY on Wed, 10/25/2017 - 17:12
Forums: 
Nodes

I have a remote M2 Rocket node that I was going to upgrade to the latest firmward but accidently got off with loading the wrong patch.

Nanostation failure?

published by KD2EVR on Sun, 11/12/2017 - 21:57
Forums: 
Nodes
After being deployed about a year, a Nanostation M2 went off the air.  When power is applied, only the power LED illuminates.  When a computer is connected via ethernet, the LAN1 LED starts showing activity, but no IP address is issued and there's no response to localnode:8080 or 192.168.1.1 or .20

I tried holding reset for 15 seconds - no change. 

Any ideas?
 

Wifi booster?

published by N1TEW on Mon, 11/20/2017 - 11:09
Forums: 
Nodes


Would this be legal or desirable on the output of say a 2g Rocket or similar?  

https://www.tomtop.com/p-c2082.html

I'm pretty sure I'll receive negative responses, but I'm curious to hear what they are. 

Thanks!  

M5 XW Help

published by n0daj on Tue, 11/28/2017 - 20:52
Forums: 
Nodes
Trying to connect a NanoM5 XW to a GS105E switch and have a useable gateway to the internet (emergencies only). The switch is configured for 3 nodes and 1 wan port. I have connected the switch to the "main" port of the Nano and it sees the computer and other devices but no internet  I have connected the switch to the "secondary" port and it will not see the computer or other devices. Any suggestions????

Doug, N0DAJ

determining XM or XW after reflash ?

published by N8NQH on Wed, 11/29/2017 - 22:42
Forums: 
Nodes

I ran across a NanoStation that I had already reflashed... but forgotten about.

Is there a way to determine what circuit board version it is - now that it has the AREDN firmware?

Used NBrM5 - got untested hardware message

published by VE3CVG on Wed, 11/29/2017 - 16:38
Forums: 
Nodes

Greetings to the list. Before I submit a report, I want to make sure that I did not do something wrong.

Tenda model AP4

published by AA4YB on Fri, 12/08/2017 - 10:26
Forums: 
Nodes
Can the Tenda model AP4 be used with AREDN?
New and trying to set up AREDN in N. Al. We have a few interested hams and have no equipment yet.
aa4yb

Far out and XM vs XW

published by W8AYN on Sat, 12/09/2017 - 21:48
Forums: 
Nodes

New to mesh and trying to sort through compatibility for my far- out QTH. Our club is just getting started, but it looks like I will be 5-10 miles from the closest likely (non-tunneled) node. It seems like I should be looking at 5.8 due to the distance.  I’m pretty high and lots of farmlands but trees nearby which may impinge on fresnel. Club members closer together looking at 2.4 so I would have to rely on my closest contact being willing to put up both 5.8 for me and 2.4 for locals. The compatibility chart shows that the Nanostation is good for 5.8 whether it is XM or XW.

Pages

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer