You are here

Home

Nodes

Your search for "30" gave back 615 results.
Results for Forum Topic

Nanostation M2 XW and M5 XW port usage standardized

published by AE6XE on Wed, 11/14/2018 - 22:22
Forums: 
Nodes
The code to standardize the port usage on the NS M2 XW and NS M5 XW has been committed to the git repository.  This means these changes will be available in the morning Nov 15, 2018 in nightly build images.    

What specifically has changed?

Before:   LAN was only on primary port, DtDLink and WAN on secondary port only.  This is inconsistent with other AREDN devices
After:   LAN/DtDlink/WAN all correctly function on main port with a single cat5 network cable like all other AREDN devices.

Additional benefit added but with limitations:

Mikrotik support

published by VA2XJM on Sun, 11/25/2018 - 15:06
Forums: 
Nodes
Hi AREDN team,

I've discussed this morning with a possible provider about the project of an AREDN mesh using Mikrotik devices. From previous posts on the forum, Ubiquiti support might be dropped because of proprietary tech in their AC line, so I decided to look into Mikrotik.

Video Tutorial on Flashing Mikrotik Device with Windows

published by km6wuh on Wed, 11/28/2018 - 00:14
Forums: 
Nodes

I made a Youtube video walking through how to install AREDN Firmware onto a Mikrotik device using Windows. It's about 20 minutes long, as I am more or less learning the process as I am going through it.

Link is here https://www.youtube.com/watch?v=7ltUHqG4A7Q

Hope it is helpful. 

Ray
KK6RAY (new call)

tp-linkv2 seems not to provide ip using dumb switch

published by K3MMB on Thu, 11/29/2018 - 10:55
Forums: 
Nodes
OK, I understand this is a user error, but

My two tp-link210v2 nodes will not provide dhcp addr when using a cisco dumb switch.

conection is

POE from power supply to 210
lan port from power connected to cisco port 1
remote rig unit setup for dhcp connection to cisco port 2

remote rig does not get ip
node shows nothing connected

regards
mike

Standardized NanoStation XM Ethernet port configuration

published by AE6XE on Sun, 12/02/2018 - 21:13
Forums: 
Nodes
The NanoStation XM devices now have fully functional ports - both main and secondary.   This capability will be in Dec 3, 2018 nightly build.   The behavior is now same as NanoStation XW devices.   POE Passthough is also functional.   

TP-Link CPE610 now available in Nightly Builds

published by AE6XE on Mon, 12/03/2018 - 22:39
Forums: 
Nodes
The changes for CPE610 are now in the code repository and will be in nighty builds from Dec 4, 2018.   Andrew KK4ZUZ has brought this device to its knees under AREDN, before OpenWrt has support for this device.   Big hand to Andrew!    The specs can be found here:

https://www.tp-link.com/au/products/details/cat-37_CPE610.html

As always, please post feedback good and bad of your experience with this device.

Joe AE6XE

 

Nanostation M2 XW low flash space

published by AJ6GZ on Mon, 07/23/2018 - 02:18
Forums: 
Nodes

Tried an update to daily 80-014217a on an NS M2 XW, reinstalled Tunnel, and it's back on the air ok.  I noticed free space for flash = 68K.  I don't recall what it might have shown before. iirc, this node went from 3.17RC1 thru a few dailies up to old 176. Not sure where it started as far as Air OS.  Could it be related to this https://www.arednmesh.org/content/bad-rocket-m5  ?

Nightly Build support for TP-Link CPE220 v2

published by KK4ZUZ on Tue, 12/11/2018 - 23:00
Forums: 
Nodes

Nightly Build support for TP-Link CPE220 v2 has been added and should be available in the Nightly Build tomorrow.

 

NanoStation M5 Can't LogIn

published by K5YKG on Tue, 12/11/2018 - 15:00
Forums: 
Nodes
Even though I have no elevation and there's no one in my NW Harris Co TX area close enough to play with, I've been operating a NanoStation M2 with all the Nightly Builds with great success. I had communicated with a Rocket M2, both on the same property, until my HF station seems to have caused it to not work, reason unknown. Could be close proximity to the 80/40m inverted-V at 1500 watts even though the Rocket has a proper shield to ground. But I digress...

Any hope for a NanoStation2?

published by AA7AU on Thu, 12/13/2018 - 19:55
Forums: 
Nodes

A fellow ham, just getting interested in Mesh, went out on his own and thought he was getting a good deal on Ebay and bought a "NanoStation2" (not M2) running factory AirOS 3.5 - I was able to upload (tftp) AREDN Nanostation "factory" firmware but it got rejected as invalid at the end of several tries.

Is there any hope for this old NanoStation2 and AREDN?

If not, perhaps there should be a warning on the Supported Platforms page for this model and the similar Bullet HP so folks wouldn't keep trying to use them???

TIA,
- Don - AA7AU

Pages

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer