You are here

Home

Nodes

Your search for "30" gave back 615 results.
Results for Forum Topic

GL-USB-AR150: Strangeness

published by nc8q on Thu, 05/09/2019 - 18:01
Forums: 
Nodes

I have a double node name ala
dtdlink.NC8Q-USB.local.mesh / NC8Q-USB.local.mesh (tun*-1)

Node Name = NC8Q-USB

However all the local mesh nodes are displaying:

dtdlink.NC8Q-USB.local.mesh / NC8Q-USB.local.mesh (tun*-1)

I have no clue why there is a double node name nor
why ('tun*-1)
?

Chuck

Ubiquiti Rocket R2AC Prism airMAX

published by 2E0FII on Mon, 05/13/2019 - 10:50
Forums: 
Nodes
Hi, 

I am looking in to setting up an AREDN in Nottingham, England, UK and so i have been looking at the hardware available and keep coming back to the newest version of the Ubiquiti Rocket M2 the Ubiquiti Rocket R2AC Prism airMAX. 

https://www.ui.com/airmax/rocket-prism-ac/ 

But it is not listed on the supported platform matrix and a Google search did not seem to come up with anything relevant. 

Does anyone know if it is suitable ? 

thanks
adam

Ubiquiti PowerBeam 5AC 500

published by NH6HI on Thu, 05/16/2019 - 19:17
Forums: 
Nodes
I was given 2 of these Ubiquiti units, PowerBeam 5AC 500. Is there any potential use for these on my AREDN system?? Can they be flashed? I don't see them in the list. These are solid units. 1 is still mounted on a tower of which we have a repeater at.
Jim NH6HI

Nightly Build 936.XXXglusb150.bin

published by KL7VK on Sat, 05/18/2019 - 12:31
Forums: 
Nodes

Subject nightly build for the glusb150 will not load. I tried it three times and receive the following message each time:

GL-USB no path to Internet

published by k0tan on Mon, 05/13/2019 - 13:06
Forums: 
Nodes

Installed AREDN firmware on a GL-USB - tnx for the thread on getting it done right, CQB! I want to dl packages, but being a USB w/o Eth ports, I haven't found a way to get a path to the Internet from either windows boxes or Ubuntu. Is there some trickery involved? (This is the only 2GHz node in town. I don't want to buy more boat anchors to play with this very fun gadget.) TIA
72, Charlie KØTAN
Mesh phone: 928 3001

Question on Participating in Columbus, OH

published by N1CTF on Tue, 05/21/2019 - 21:23
Forums: 
Nodes
Hello to the group, I am interested in setting up a node in Columbus. I am in NW Columbus, across from the State EOC, very near Dublin-Granville Road and Sawmill Road. Not sure if I will be better off working with AC8YE or WB8CJW. Can you advise with instructions or a point of contact to get started? Also, what is the most preferred equipment for this range? Thank you, John N1CTF

Nanostation M2/M5 Mimo firmware flash error

published by va3itg on Thu, 05/23/2019 - 07:35
Forums: 
Nodes

Hi All,

new to AREDN and just getting started. I have a few Ubiquiti nanostations... M2 M5 Mimo devices.
I tried to flash one last night via tftp and was not successful.

I received this error: Error on server : Firmware check failed

I followed the instructions that are posted on this site.
The device is in the right mode, 1,3 & 2,4 lights flashing alternately

This is the command line I'm using: tftp -i 192.168.1.20 put c:\temp\aredn-3.19.3.0-ubnt-nano-m-xw-factory.bin

GL150 USB No radio activity

published by ve6vh on Wed, 05/29/2019 - 14:51
Forums: 
Nodes
Hi All,
I recently acquired two GL-150USB microuters from Amazon. Both come up with the original code, I set the default password as required and flashed one with the current 960 load from the nightly builds, and the other with the 902 load which was given to me and has worked on previous occasions. Both appeared to flash properly, they came up with the NOCALL page, I was able to set the parameters for the MeshRF and reboot to obtain a 10.x.y.z address in both cases.

Replacement for Ubiquiti Air Gateway LR ?

published by ZS1I on Fri, 05/31/2019 - 07:43
Forums: 
Nodes

It would appear that the Air Gateway has been discontinued. Any suggestions for a replacement. The Ubiquiti Cube is not an option as it has no external antenna.

NanoBridge Ethernet port configuration

published by al1q on Wed, 06/05/2019 - 21:39
Forums: 
Nodes
Good evening!

Do the main and secondary ports on the NanoBridge work the same way as the NanoStation, as per this article?

https://www.arednmesh.org/content/standardized-nanostation-xm-ethernet-p...

Thank you!

Jeff Stidham AL1Q

Pages

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer