You are here

Home

Nodes

Your search for "30" gave back 615 results.
Results for Forum Topic

Support for Mikrotik rb-952ui-5ac2nd

published by VE3CVG on Thu, 02/07/2019 - 10:30
Forums: 
Nodes
I am experiencing a problem with the Mikrotik rb-952ui. Sorry if this has already been documented but I have not found it stated this way. 
Scenario 1 - If I set the RF for 2397MHz / 5MHz and connect port 5 to a unmanaged switch and then to a nearby NanoBridge on 2397MHz / 5MHz (also plugged into the same switch), the Mikrotik sees the NanoBridge via dtd but not via RF. It does not see a NanoStation on 2397MHz / 5MHz which is only 30 feet away, on the same frequency, via RF.

NanoStation Crash

published by WA3LAB on Tue, 02/12/2019 - 11:52
Forums: 
Nodes

I had a brand new Nanaostation M2 mounted on a 20 foot pole that fell over and of course the Nano managed to find the sidewalk.  The case is cracked so I took it apart to survey any other physical damage.  The PC board has no obvious damage, but the metal cover on the RF section had popped off.  I powered it up and it appears to boot up but now it is transmitting on channel 11 at 20 mhz bandwith where it had been at channel -2 and 5 MHZ bandwith.  Also the LAN ports appear to be dead.  I tried to set up for a TFTP reflash, but I can't get a ping on the LAN port.  So I did a few hours of res

Nightly Build support for TP-Link CPE510 v3

published by AE6XE on Mon, 12/10/2018 - 19:36
Forums: 
Nodes

Andrew KK4ZUZ (coding) has been working with Jean-Michael VA2XJM (with the test hardware) to add support for the latest version of the TP-Link CPE510 device, now at hardware rev v3.   This will be in the Nightly Builds from Dec 11, 2018.

Yet another round of applause and thanks!

Please post usage experience here.

Joe AE6XE



  

Nightly Build for Picostation M2

published by kc5hwb on Sat, 02/16/2019 - 10:46
Forums: 
Nodes

Unless I am mis-reading something, I am not seeing a nightly build for the Picostation from Ubiquiti, is this correct?  Or is it called something else?  I've loaded nightly builds for the Air Router, Nanostation and Bullet with no issues, so I would like to put one on my PIco also, but not finding it.

73

Bullet 2HP (FCC ID: SWX-B2)

published by KC7HEX on Sun, 02/17/2019 - 19:42
Forums: 
Nodes
I have acquired a Bullet 2HP (FCC ID: SWX-B2) and it has a non-functioning reset button on the unit and when I try to use the POE reset, it does go into the proper light sequence for a reset.  It will not take the AREDN firmware like my other two Bullet (which are the Bullet M2 (FCC ID: SWX-M2B)).  I did go the the UBNT web browser and was able to upload the Bullet to a more current firmware of XS2.ar2316.v4.0.4.5074.150724.1340

NanoStation M2 - POE on Secondary Port

published by AF6FB on Mon, 03/11/2019 - 22:59
Forums: 
Nodes
Hello,
I have a NanoStation M2 running 3.18.9.0. Is there a way to turn on pass thru POE? I would like to run a second NanoStation by daisy-chaining them.

I found some old notes talking about a setting in the Advanced section, but the only setting I have there is "Advanced Mesh". But, these were on an older version of the firmware.

What am I missing?

Michael AF6FB





 

Firmware update failed

published by w8erd on Sat, 05/30/2015 - 11:16
Forums: 
Nodes

I tried to install AREDN firmware on a Bullet M2, which previously had BBHN firmware.

As soon as I clicked on the update button, everything stopped. No messages, now window, nothing.

Now I cannot communicate with the Bullet at all.

What can I do now?

Thanks!    Bob W8ERD

NBE-M2-400

published by W7ADD on Fri, 09/16/2016 - 17:47
Forums: 
Nodes
I have a NBE-M2-400 from another project, any suggestions on giving it a try with AREDN?

Douglas
W7ADD

bricked Nanostation M2

published by kj6dzb on Thu, 08/23/2018 - 01:32
Forums: 
Nodes
Hi All,

I bricked the firmware on a NS M2 downgrade. Dose any one have expertise & willing to take the node and jtag flash it? Im willing to buy you a beer + shipping.


73 Mathison   

Bullet M5 XM TFTP stops when trying to upload firmware

published by N4RT on Sun, 03/17/2019 - 21:18
Forums: 
Nodes
Need some help to figure out what I'm doing wrong.

I have successfully flashed other M5 devices including those with XW chip sets.  This is a Bullet M5 with XM chip set running AirOS 6.1.9.

I can put the Bullet in TFTP mode with alternating LEDs as expected and I am using the Windows 10 TFTP client to transfer the 3.18.9.0 firmware.  As soon as I hit the enter key after typing in the TFTP command string, the alternating LEDs on the Bullet STOP and it just sits there.

Pages

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer