You are here

Home

Nodes

Your search for "30" gave back 615 results.
Results for Forum Topic

Unbricking a Node by KD4RSX

published by KD4RSX on Wed, 12/13/2017 - 13:50
Forums: 
Nodes
How to unbrick a Node when you see no IP address from the Node and AREDN U-Boot Test gives you error message when you Ping.
 
Things to look for on your Node AFTER you take it out of its case.
You need to look for the 4 pin Cmos Connection. (On my NanoBeam M2 I had to solder pins in the holes. Yes, I know, NanoBeam not supported but I unbricked it too.)
You need to find what pin is Ground with a continuity checker.

Nodes for sale

published by K8KO on Wed, 01/10/2018 - 10:18
Forums: 
Nodes
 

I have for sale the following equipment:

1. One Ubiquiti airRouter AR flashed with 3.16.1.1 firmware.

2. One Ubiquiti airRouter AR flashed with develop-169-dlb-d14f3  firmware.

3. One Ubiquiti Nanostation M5 (XM) flashed with 3.16.1.1 firmware.

4. One Ubiquiti Nanostation M5  flashed with develop-169-dlb-d14f3  firmware.  This one was working OK, but for reasons unknown it is no longer accessible.  Hardware seems OK, so I assume it is the software.

Each of the above is used, has not been installed outdoors, and comes with OEM power supplies.

Rocket M5 upload grayed out

published by KB8TEP on Wed, 01/17/2018 - 18:31
Forums: 
Nodes
After successful install of nightly build (develop-171-69937359), to a Rocket M5 XW, no upload buttons are available. 

900 MHz

published by N8JJ on Tue, 10/24/2017 - 08:16
Forums: 
Nodes
I haven't seen anything on 900 MHz nodes recently, so I thought I'd start a new thread.

I setup a M900, with AIROS 5.6 to see what the interference looked like.
It looked pretty good.  Noise floor was between -100 and -96 dbm.
I didn't see any strong signals in the band.
So I setup an AP with a 10 MHZ bandwidth and 28 dbm.  (nothing is connected now)
I started to notice some odd behavior from my home automation system which is a "Smartthings" system from Samsung.
I have a dozen sensors and devices and some of them would stop working for a while.

Node internet access

published by NH6WR on Thu, 02/08/2018 - 13:07
Forums: 
Nodes
What are the correct Set up settings for a node to have internet access for the purpose of the AREDN map?   We have a Pi on the node that sees the internet but for some reason after clicking  "Upload data to AREDN Servers"   I receive the message  :  ERROR  Cannot update map.  Please ensure this node has access to the internet.
Thank you-
Jim, NH6WR

AREDN hardware futures?

published by KQ9P on Tue, 02/13/2018 - 13:23
Forums: 
Nodes
Hi everyone

Please take this as a constructive question, because that is what I intend.  I am enthusiastic about amateur radio mesh technology and its application to public service and emergency communications.  I am deeply grateful for the hard work and creativity of the AREDN team.  I am currently operating a two-node mesh in Charlottesville, VA, and actively seeking sites to expand and enhance the network.  Our county public safety communications folks are excited about the possibilities.

mesh not working

published by KW5X on Sun, 03/04/2018 - 20:39
Forums: 
Nodes


I have been following the build out of the AREDN net from Orange and San Bernardino Counties for the past 6 months.  Now that Snow Peak has a node pointed East I should be able to find the signal from Snow by setting up my NanoBridge M5 in a location visible from Snow Peak.  I have tried 3 locations and not been able to log onto the mesh.  Likely I am not getting lined up properly with the signal from Snow, but I decided to try a test at home.  I pointed the NanoBridge M5 at a NanoStation M5.  of course the signal is strong between the 2 nodes but still the mesh does not run. 

Will work to add Internet and IP Camera?

published by AL7MH on Sat, 03/24/2018 - 10:57
Forums: 
Nodes

/sites/default/files/sites/default/files/pictures/user2213/Improved%20AL7MH%20AREDN%20Node_0.pdf

Will this work to add internet, tunneling, and an IP camera to an ARDEN Node?

Clarity on current flash procedures

published by N7TZK on Fri, 03/16/2018 - 19:07
Forums: 
Nodes

Our ARES group hasn't purchased any new nodes for sometime, but we are now planning on purchasing some PBE-M5-300 and NS-M5 nodes.  I find it a bit hard to know for sure what the proper procedures are now, so before I risk bricking new nodes, I'd like to verify I understand correctly.

AREDN 3.16.1.0 Help file

published by AC2OG on Mon, 05/28/2018 - 06:53
Forums: 
Nodes
Hello,
this is to inform that I have translated into italian the AREDN 3.16.1.0 help file.
If you consider it usefull for the community, I can make it available.
73, de Leo I3RKE/AC2OG 

Pages

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer