You are here

Home

Network Switches

Your search for "29" gave back 121 results.
Results for Forum Topic

TP-Link TL-SG108E configuration quirks

published by KG7LMI on Thu, 05/24/2018 - 02:17
Forums: 
Network Switches
I read earlier that the TL-SG108E could now be used for Internet gateway applications with the latest firmware, so I gave it a try for the project I am working on. At first, I was not able to reconfigure VLAN 1 - it kept hanging the switch. I discovered that you have to define all the other VLANs first, while also ensuring that all ports are in at least 1 VLAN. Then, and only then, you can redefine VLAN 1. Finally, you can assign the PVIDs as needed. In summary:
1. Add new VLANs
2. Verify that your final config will assign each port to at least 1 VLAN

AirGateway Configuration Problems

published by K3GX on Sat, 05/26/2018 - 22:31
Forums: 
Network Switches
OK, I'm wading into this bridging and VLAN stuff, so let me try to explain what I'm trying to do... Maybe it's not possible with the Ubiquiti AirGateway.

I have a Ubiquiti NanoStation connected to the POE port (LAN0) of the AG. I would like for the NS to provide DHCP services to the wireless WLAN0 port. At a minimum, I would also like to be able to access the AG management through the AG LAN port (LAN1). I do not want AG management to be possible on the mesh.

can you reflash a TP-LINK TL-SG108E switch?

published by K3MMB on Fri, 04/17/2015 - 10:32
Forums: 
Network Switches

I wonder if there is a firmware replacement for switchs that allow VLAN configuration?

73 de mike

Need VLAN Help

published by K3GX on Thu, 08/09/2018 - 10:23
Forums: 
Network Switches

Being a newby (or noob) to VLANs, I'm looking to set up the network shown in the picture below while using the VLAN configuration recommended on the forum. After much research, I still have quite a few questions:

Setting up an EdgeRouter X for AREDN use

published by AE6XE on Sun, 04/23/2017 - 17:49
Forums: 
Network Switches
I put together tho following instructions to configure a Ubiquiti EdgeRouter X for AREDN typical deployment.  Would appreciate others helping to proof read and validate these instructions.  Any EdgeRouter's out there?  

https://drive.google.com/file/d/0B2bEy75HhwWhMFY0SXRkczV4eDQ/view?usp=sh...

Joe AE6XE

GS105e v2 typical install

published by VE9GIS on Wed, 11/21/2018 - 19:38
Forums: 
Network Switches
Confused by all the choices.  I want to link the internet, my Ubiquiti Nano node and a Win 10 laptop.  ​Netgear Prosafe GS105e v2 what would be a typical install.

Misha
Moncton, NB, Canada
FN76

best buy for vlan and poe

published by K3MMB on Wed, 11/28/2018 - 13:37
Forums: 
Network Switches
What is considered best approach to adding a poe and vlan device to a working mikrotik/tp-link mesh??

regards
mike

TP-Link TL-SG108PE - VLAN help is needed.

published by VA2XJM on Mon, 12/10/2018 - 21:33
Forums: 
Network Switches
Hi everyone,

It is my first time playing with VLANs and so far I'm not that much successful!

So I have a TP-Link TL-SG108PE switch. I've been looking at this page (https://www.arednmesh.org/content/tp-link-tl-sg108e-network-switch) to start with a basic configuration but it doesn't seems to be right (nothing works). So far you can see below what VLANs I have configured:

Which to use?

published by KB9MTD on Mon, 12/17/2018 - 18:22
Forums: 
Network Switches
Greetings!

I have a couple pieces of equipment in which to assist with networking within my QTH.  I have a question in regards which to use and really how to set it up.

The first is a Cisco Catalyst 3520-C PoE.  This is actually what I'd like to use since it is PoE compatible. I just don't know exactly how to set it up at the moment. I do have it at stock settings currently so it should be fairly easy to setup. Also I know my way around it a little.

newbie questions on vlan switch and bullet

published by wa2ise on Mon, 05/16/2016 - 15:18
Forums: 
Network Switches

Some questions on separating the LAN and the WAN of a bullet, I have a linksys router with OpenWRT on it.
I'm a newbie trying to figure this out.  I figure that this diagram of an ASUS router is valid as describing my OpenWRT Linksys rouyter: Yes?
Looking at this (from the OpenWRT website)

Pages

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer