You are here

Home

Network Switches

Your search for "29" gave back 121 results.
Results for Forum Topic

GS305E

published by AH6LE on Sun, 06/13/2021 - 16:53
Forums: 
Network Switches

I've looked at the various Netgear config pages for how to setup a GS305E switch for deployment at one of my sites. Here is the configuration I'm shooting for:

One PBE400 connected to the Mesh
A 2nd  PBE400 used to allow others to connect in order to access the Mesh
Raspberry Pi (used for Allstar) that uses the Mesh to connect to my other Allstar nodes
Yaesu Fusion repeater to connect to the Mesh


I thought this might be the method to use:

EdgeSwitch 10XP POE Spec

published by k6dlc on Thu, 08/26/2021 - 12:20
Forums: 
Network Switches
   I would like to know the POE spec on a EdgeSwitch 10XP? The reason for the question does if have the specification on handling a Ubiquiti Rocket M5 Omni that has a Rocket M2 POE that is getting the power from the M5? 

Unifi P M5-400

published by KJ7ITZ on Mon, 09/06/2021 - 13:40
Forums: 
Network Switches

Howdy,
since my 2 primary switches don't vLan,
I think my only option to change the LAN on the powerbeam dhcp so it doesn't interfere with the main dhcp scope.
and match the ip segment i currently have.

KJ7ITZ

TS5-PoE config

published by KJ7ITZ on Tue, 09/28/2021 - 23:53
Forums: 
Network Switches
howdy,
I dont know why but I am missing the line from A to B.
pB400 config,
Mesh RF 10.236.177.149/8
Lan 10.101.140.169/29
WAN DHCP ( from RPI4 10.1.1.2 )

SInce the pb400 has 1 eth, i made bridge from an RPI4, eth is 10.1.1.1/28 (dhcp to pb400) bridges to Wlan0 172.16.5.x to the internet router of 172.16.5.1
Which TS5 config is this? 2 LAN 2 NODE 1 WAN?


pb400 <>TS5port?
radio pc<>TS5port?
RPI4_bridge<>TS5port5

Thank you for your support.
KJ7ITZ
 

Getting connected to configure EdgeSwitch 5 XP

published by KD7DHO on Sat, 09/25/2021 - 17:57
Forums: 
Network Switches
Simple question, how do you connect the EdgeSwitch 5XP to the laptop to configure 3 ports for POE operations and 2 ports for LAN operations.  The unit looks like the ToughSwitch I'm replacing, but I didn't set that one up.  The tutorials I'm seeing on Youtube already have the Switch linked to the laptop and a nanostation.  I need the instructions to making the connection and setting up in the browser to be able to configure the unit.  I've done that in the past with bullets and nanostations, but not with the EdgeSwitch.  I'm wishing I had the computer expertise to do this without help, but I'm

Configuring an EdgeRouter X for use with AREDN networks

published by k6dlc on Wed, 12/08/2021 - 20:17
Forums: 
Network Switches
  Would someone update the instructions for the edgerouter x? The new web firmware hs been chnaged.

MikroTik RB260GSP

published by KV3T on Fri, 03/11/2022 - 18:41
Forums: 
Network Switches

This managed smart switch, the MikroTik RB260GSP is a 5 port, 4 with passive PoE out.  It works great with AREDN, and can be configured with VLANS as needed to tunnel, DTD, or whatever you need via their simplfied SwOS (much easier than their typical RouterOS software).  I just noticed that there is a seller on ebay selling these starting at $25 ea.  I'm bidding on one of them, but there are 7 others that are fully functional at that price, plus a few more with a few ports not working.  For anyone looking for a cheap, fully functional, switch, I'd get one or two.  Also, they can be powered

Newbie queston on Netgear GS105eV2 set up

published by WM6Q on Fri, 02/07/2020 - 17:06
Forums: 
Network Switches
I'm sure this is basic, but I am lost on all the networking set up. I have a Mikrotik routerboard tunneling to the AREDN mesh through a hardwired internet connection. I also have two RF nodes: an 18inch dish and a Nanostation. I would like to be able to access each of these three nodes from my computer. I have all three nodes plus the computer plugged into the Netgear GS105eV2 switch. I am only able to access the routerboard. How do I select what I can connect to?

Thanks!!

Bob WM6Q

PowerBeam M5 works

published by KK4IB on Sun, 04/03/2022 - 09:42
Forums: 
Network Switches
WE set up a new Ubiquiti PowerBeam M5 300 ... it programmed with AREDN MESH no problems. It was connected it to a Mikrotik HAP-AC-Lite 5th port (PoE). It set up correctly, all parameters. The network found it. Then it connected to a stand-alone Ubiquiti Bullet M5 (once the frequencies were set to the same), and the network is tunneled.

We approve the PowerBeam M5, ... KK4IB and KC4JIR, Middle GA network [www.ga-aredn.lumasis.net; ga-aredn-users@groups.io].

Perplexed - Hap AC Lite assigns IP but Camera not Pingable

published by W5SAT on Mon, 05/09/2022 - 13:59
Forums: 
Network Switches

I can't figure out this problem.  For a couple of weeks, I had an Amcrest IP camera on one of the LAN ports of my MikroTik hAP AC Lite working just fine.  A few days agao, I realized I couldn't access the camera.  Checked all of the usual things but couldn't access the camera even though the AC Lite was assigning a DHCP address.  I put the camera on my home router, it got a IP address and worked fine.  I factory reset the camera, tried again on the AC Lite and still can't ping or access the camera in any way and can't pull in a RTSP stream either.  Tried a differnt Amcrest IP camera and the

Pages

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer