You are here

Home

Network Switches

Your search for "29" gave back 121 results.
Results for Forum Topic

DtD Port on MikroTik hAP ac2?

published by KM6ZJT on Wed, 04/26/2023 - 14:17
Forums: 
Network Switches

I am currently using a MikroTik hAP ac Lite in my mesh setup. It has a MikroTik LHG dish connected to port 5 using DtD. I also occasionally use the WAN port (port 1) if I need to do upload load updated location information to the AREDN map.

RB750P-PBr2 4 node POE switch

published by nc8q on Sun, 07/28/2019 - 14:25
Forums: 
Network Switches

Solved, finally.

TP-Link EAP 110, will it work?

published by kp4djt on Mon, 06/19/2023 - 13:40
Forums: 
Network Switches

I have a couple of these access points, I do not see anything about them but then there are other devices that I have found are not listed but are working. 

Does anyone know if these can be put into AREDN service?
 

TP-Link EAP 110, will it work?

published by kp4djt on Mon, 06/19/2023 - 13:27
Forums: 
Network Switches

I have a couple of these access points, I do not see anything about them but then there are other devices that I have found are not listed but are working. 

Does anyone know if these can be put into AREDN service?
 

MikroTik hAP ac3 - Switch vs Mesh Config

published by KI6CVM on Tue, 11/21/2023 - 11:59
Forums: 
Network Switches

I am building out a node and I have been looking at using the hAP ac3 as a switch and to provide standard WiFi (not mesh RF).

Does the Arden firmware for this unit automatically configure RF for the mesh network?

My best case scenario is the firmware will do switch configuration (VLANs, DHCP forwarder, etc) but leave the RF as standard WiFi.

Given my scenario am I better served running OEM firmware and manually configuring networking?

Thanks in advance,

-JP

HAP AC LITE VLAN CHANGE NEEDED

published by AA3JC on Sun, 12/10/2023 - 10:07
Forums: 
Network Switches
I need to make a change on my HAP AC LITE, from the standard VLAN configuration to allow LAN AND DTD traffic on port 5 that already supports DTD on this port 5. The purpose is that I have a 26 port smart switch that is configured for all my nodes with LAN ports configured for each node, 
simular to the Aredn Docs for the Netgear GS108E. I know my switch is configured correctly as when I plug a node (not the HAP) into a configure node port, the configured LAN ports all work as expected.
 

Ubiquiti Air Router config access

published by N4SV on Mon, 01/08/2024 - 20:43
Forums: 
Network Switches

I have an old Ubiquiti Air Router flashed with AREDN.  I wanted to access the management interface but it doesn't seem to respond.  According to old docs it should be on 192.168.1.1 but not seeing any response from this IP when I attempt PINGs.  Once AREDN is installed how can you access the management interface, to list current config or change port VLAN assignment or the like.

MikroTik Tutorial

published by AJ6GZ on Sat, 03/10/2018 - 17:21
Forums: 
Network Switches

Mikrotik has a huge variety of routers, wifi devices, and circuit boards (“RouterBOARDs”) which all run their RouterOS. They also have some switches running SwitchOS. We will concentrate on the Routers as they are most flexible for what we are doing. Below is guide on configuring these devices to support AREDN nodes and hosts, Pi, phones, cameras, etc.

MikroTik RB750 router

published by kg7kmv on Mon, 08/12/2024 - 11:35
Forums: 
Network Switches
I've been at this for a few days, and while I have certainly climbed the learning curve, I'm not competent on this.
I have an RB750up. A discontinued model, but still very useful with current manufacturer FW and OS. I want the 4 PoE ports to run 3 nodes at a site. I have setup a few of these, but just as a basic bridge with no vlan anything. But I have a new case where I need WAN to get through.

Pages

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer