You are here

Home

Hardware

Your search for "28" gave back 1043 results.
Results for Forum Topic

Second attempt with nanostation loco M5, no Ethernet problem

published by AA6E on Thu, 06/28/2018 - 18:03
Forums: 
Nodes

Results with "clean" install on second brand new NanoStation loco M5 (XW):

 

1. Replace AirOS 6.06 with 5.6 via TFTP

2. Replace AirOS 5.6 with 5.5 via AirOS update

3. Replace AirOS 5.5 with AREDN-develop-176-8c5be0cf-ubnt-loco-m-xw-squashfs-factory.bin

==First, with AirOS upgrade ---> leads to dead Ethernet problem (no response to DHCP discovery)

==Then repeat with TFTP install ---> dead Ethernet again

 

I do get WiFi access through the "MeshNode" SSID.

Bricked and no IP address

published by WD6EBY on Wed, 08/08/2018 - 18:26
Forums: 
Nodes
Hello All,
Well I finally bricked a unit.  Unfortunately it is a 3G Rocket.  I tried TFPT with no luck.  Angry IP IP Scanner and it shows no address.  I successfully counseled into the jtag port and the boot loader stops at booting...  

From the terminal I entered the command  'urescue -f -e and received the response;
'boot loader overwrite mode'
'starting tftp server...'
'using eth0 (192.168.1.20), address: 0x81000000'
'waiting for connection:/\/\/\/'

Port mapping on AirRouter, 1 is DtD instead of 4

published by DL4FLY on Wed, 08/08/2018 - 10:35
Forums: 
Nodes
Hi,
i set up two AirRouter with nightly build aredn-120-xxx.
Notebook on Lan Port 1 and M5 loco on Port 4 did not work.

Notebook gets a DHCP on Port 4 and Node is visible when connected on port 1.
So VLAN function seems to be switched.

Please change the picture under https://www.arednmesh.org/content/how-use-airrouter-ports if this behavior is intended.

Rocket M2 XW

published by al0y on Sat, 08/18/2018 - 16:49
Forums: 
Nodes
Hello, all... 

is the Rocket M2 XW version supported (even on nightly builds) or only the M5?
The supported platform matrix mentions only the M5 as supported, and I don’t see a reason why wouldn’t the M2 be as well. 

Thanks in advance

As my bullet has only one ethernet jack, is it a LAN or WAN?

published by wa2ise on Sat, 05/14/2016 - 21:00
Forums: 
Nodes
Just acquired and installed AREDN on a Bullet Titanium M2, and it appears to be working, and have a tunnel client running as well.  But I may have it configured poorly?  I have the WAN disabled, and the LAN set to NAT, and the IP to 192.168.1.86 mask 255.255.255.0 gateway 192.168.1.1 and DHCP disabled.  The tunnel works like this.  The only ethernet jack on this thing appears to be a LAN jack (when I first tried to set it up, I couldn't connect to it until I did a ipconfig on my PC, and found I had an IP address belonging to the LAN part.   I have it on channel -2 with a 5MHz setting.  

Airgrid M2 2G20

published by W8MRL on Sun, 09/16/2018 - 11:38
Forums: 
Hardware

I'm about to buy the following and wanted confirmation that they can be flashed.  As I read the list, they can be.  They are airGrid M2 HP AG-HP-2G20
Can someone more knowledgeable confirm it for me?

Thanks,

Rob

Windows security issue

published by K8HMF on Tue, 02/27/2018 - 15:01
Forums: 
Nodes
Hello all!   I am just getting started with AREDN mesh networking. Managed to get a couple Nanoloco M2s and a Bullet  setup. However now when I access the webpage a Windows Security page requests a username and password. During the initial setup I used the "root" and "hsmm". I changed the username to "k8hmf-001" and a new password. All seemed to work OK. Today my username and password will now work. Any thoughts?

bulletm2-hp v5.6.11 (downgrade...but!...)

published by kk4zuu on Wed, 09/26/2018 - 16:41
Forums: 
Hardware

Good day,

I acquired a new US model Bullet M2-HP (mfr  test date: 10/23/17), the installed AirOS sw is v5.6.11 (XM).

On the Ubiquiti AirMax Legacy Software Download Site for this model (URL) I only see the following legacy version for download:

https://www.ubnt.com/download/airmax-m/bulletm/bm2hp
- no v5.5.x versions shown

Which Ubiquiti units have 64 megs of RAM

published by W8MRL on Fri, 10/12/2018 - 18:39
Forums: 
Nodes
I have a Bullet M2 with tunnel and meshchat installed.  It doesn't always boot completely and is very slow.   
I've removed the tunnel package and it is much peppier but now I've lost the tunnel.  So, I guess I'll have to buy a 64 mB unit but I don't know what to get so I'm looking for input.

I have a parabolic antenna with an N-connector on it and hope not to have to buy another antenna.

Questions regarding the Mikrotik hAP ac lite

published by AC0WN on Mon, 10/15/2018 - 22:07
Forums: 
Nodes

First a sincere thank you to everyone associated with the AREDN project for developing and providing such amazing communication tools.  smiley

Now a few questions regarding the Mikrotik hAP ac lite when configured with the latest AREDN firmware:
1.  Can the 2.4 ghz radio be turned off?  I'm using the device as a local node and tunnel server and would prefer to eliminate the unnecessary RF.

Pages

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer