You are here

Home

Hardware

Your search for "28" gave back 1043 results.
Results for Forum Topic

Clarity on current flash procedures

published by N7TZK on Fri, 03/16/2018 - 19:07
Forums: 
Nodes

Our ARES group hasn't purchased any new nodes for sometime, but we are now planning on purchasing some PBE-M5-300 and NS-M5 nodes.  I find it a bit hard to know for sure what the proper procedures are now, so before I risk bricking new nodes, I'd like to verify I understand correctly.

AirGateway Configuration Problems

published by K3GX on Sat, 05/26/2018 - 22:31
Forums: 
Network Switches
OK, I'm wading into this bridging and VLAN stuff, so let me try to explain what I'm trying to do... Maybe it's not possible with the Ubiquiti AirGateway.

I have a Ubiquiti NanoStation connected to the POE port (LAN0) of the AG. I would like for the NS to provide DHCP services to the wireless WLAN0 port. At a minimum, I would also like to be able to access the AG management through the AG LAN port (LAN1). I do not want AG management to be possible on the mesh.

AREDN 3.16.1.0 Help file

published by AC2OG on Mon, 05/28/2018 - 06:53
Forums: 
Nodes
Hello,
this is to inform that I have translated into italian the AREDN 3.16.1.0 help file.
If you consider it usefull for the community, I can make it available.
73, de Leo I3RKE/AC2OG 

Ubiquiti air Router HP

published by N5MXI on Thu, 05/31/2018 - 09:00
Forums: 
Nodes

I have a  Ubiquiti air Router HP with firmware version XM v.5.6.2. I would like to flash AREDN on the ARHP. I understand I must downgrade to  v.5.5.?. I am confused which firmware I load to accomplish the downgrade because there are 2 listed.

http://dl.ubnt.com/firmwares/XN-fw/v5.5.11/XM.v5.5.11.28002.150723.1344.bin or

Nanostation loco M5 (XW) - can not config nor recover

published by N2JWC on Tue, 05/15/2018 - 22:40
Forums: 
Nodes
Good day fellow hams. So as many the latest hardware is the newer XW, I used the code specific for the XW.  Firmware seemed to take just fine, now the LEDs on the back show power (green), ethernet activity (flashing green) and the FAR right LED is green.  Best I can tell this means all is normal, however when I change my NIC to DHCP I never receive an IP address from the NSM5 loco.

can you reflash a TP-LINK TL-SG108E switch?

published by K3MMB on Fri, 04/17/2015 - 10:32
Forums: 
Network Switches

I wonder if there is a firmware replacement for switchs that allow VLAN configuration?

73 de mike

WIFI access

published by K9LRD on Sat, 07/07/2018 - 18:32
Forums: 
Nodes

I need some help with seting up a wifi access to the Aredn network. I have a Netgear GS105e setup with a WAN port. Not sure on how to setup up the access. It is a Ubiquiti Bullet2. Maybe this has been addressed and I'm looking in the wrong spot. Thanks for the help

Version 2 of CPE210 V2 incompatable with AREDN?

published by W9EO on Sun, 06/04/2017 - 11:19
Forums: 
Nodes

So I just purchased the TP Link CPE210 off amazon and received hardware Version 2 of the device and  was unable to flash the stable version of the firmware. I got the message with both the current nightly firmware build and stable "hardware not support" error. Yes I shortened the file names on both attempts.

Loading Firmware on to PowerBeam M5 400-ISO

published by N3BKV on Tue, 06/12/2018 - 20:41
Forums: 
Nodes
What would be the best way to load firmware on to a PowerBeam M5 400-ISO?  Can I just take a nightly build (if so which one is best - I see a few posts saying I should use the Rocket firmware) and just TFTP it on to the node or do I need to downgrade to Air OS 5.6.15 then 5.5 and then upload the firmware via TFTP or the GUI?

I just want to make sure I don't brick the node.

Thank you,

Dave

My portable AREDN node

published by AL7MH on Wed, 03/07/2018 - 10:48
Forums: 
Nodes
  1. NanoStation M5. ($82 from Amazon)
  2. Tripod with 18-foot Mast.
  3. 12-volt battery go box.
  4. DC POE injector ($9 from Amazon).
  5. Ubiquity airGateway ($23 from Amazon) for 'remote wifi connection to Windows, Mac, or iPad.
  6. Microsoft Surface Pro with Chrome web browser to talk to airGateway and Nanostation, MeshChat, Winlink Express for ptp email.

Ethernet cord is about 10 feet and station seems to be fine with 12-volt (instead of 24-volt Ubiquity spec).  Draws about 0.17 amps.  Doing longer term testing.

Pages

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer