You are here

Home

Possible Bugs

Your search for "22" gave back 150 results.
Results for Forum Topic

Possible security issue with build 556

published by AC0WN on Thu, 12/13/2018 - 21:29
Forums: 
Possible Bugs

I have build 556 on a hAP AC lite and I love the ability to turn off the RF mesh side on 2.4 Ghz.  It's also great that you can use either the 2.4 Ghz radio or the 5 Ghz radio as an access point.

However ....  after configuring the 5 Ghz radio as an AP on channel 149 the node is still advertising the SSID "MeshNode2G" as an unsecured network.  I can log on this network without a password and use the mesh as well as the wan side (which I am doing now to post this topic).

Tunnel setting changes cause nodes to stop responding

published by K6CCC on Thu, 04/16/2020 - 12:38
Forums: 
Possible Bugs
Executive summary version:  Saving changes on Tunnel Client or Tunnel Server page results in node becoming unresponsive for a while (10 - 120 seconds).

Nanostation M5 XW

published by N7JYS on Tue, 02/18/2020 - 09:49
Forums: 
Possible Bugs

After upgrading to NB 1326  on  a NSM5  no access to tftp on 192.168.1.20. 


Eric

Not a bug, but

published by w6bi on Sun, 04/12/2020 - 16:49
Forums: 
Possible Bugs
So, the AREDN alerts are working properly, but what's to be done with this:

AREDN Alert(s):
(QST): AREDN v3.20.3.0 has been released

When the node is running a nightly build more current than that?  Maybe add it as a second line ("Latest nightly build is xxxx")?

Orv W6BI

Issue with Nightly Build Firmware

published by AC2OG on Sat, 06/20/2020 - 06:17
Forums: 
Possible Bugs
Hello,
to connect with the aredn tunnel server I have been requested to install a Nightly Build Firmware.
After some days of using the nightly Built Release "aredn-1601-d06bbaa-ath79-ubnt_bullet-m-sysupgrade.bin" I report the following problems:
A). I can’t connect to my node with http://localnode:8080 but only with the IP address. When I try to connect with "localnode:8080" I get this error message:
"not possible to find the IP address of the local node server. DNS_PROBE_FINISHED_NXDOMAIN.".

Whoops! OLSR is not running, try again later.

published by gm7urd on Thu, 02/21/2019 - 05:33
Forums: 
Possible Bugs

Hi Guys,

Recently updated to latest firmware, 3.18.9.0

Im receiving “Whoops! OLSR is not running, try again later.” 

No nodes displayed.

The device is an AirRouter set to client tunnel mode, also linked via RF. 

1. Tunnel client shows active connection
2. RF nodes are seeing the AirRouter
3. RF nodes cannot see anything past AirRouter
4. Have power cycled several times and waited a few hours... No change.

Any suggestions?

Unable to install tunnel FW on 3.20.3.1 on Rocket M5 XM

published by K6CCC on Fri, 07/10/2020 - 01:35
Forums: 
Possible Bugs
Updated one of the Rocket M5 XM nodes from Nightly 1642 to 3.20.3.1.  The firmware update went perfectly.  Then tried to install tunnel software on the node.  I get:
ERROR:
Package update failed!

Tunnel software needs to be installed.

I have tried the tunnel install many times along with many reboots.  Same result.
At the suggestion of Eric - KG6WXC, I did a logread immediately after the install failed.  There was absolutely nothing in the log for the time involved.

OLSR Storm

published by K6CCC on Tue, 08/04/2020 - 13:08
Forums: 
Possible Bugs
First I am going to define OLSR storm because that is not an official term, but it is being used here in Southern California.  What we call an OLSR storm is a condition where OLSR packets are being distributed in such a manner that it functionally crashes the mesh network.  The symptoms include that nodes can not be seen, or link qualities plummet network wide.  This specifically includes DtD links and tunnels - you know there is a problem when a DtD link shows a LQ of 10%!  Usually eventually the storm will subside by itself, but that can take several hours.  Manually breaking links (usually

Mikrotik "UNTESTED HARDWARE" on new RBLHG-2nD

published by KE0NA on Sat, 10/17/2020 - 20:21
Forums: 
Possible Bugs
A friend and I recently purchased two new RBLHG-2nD's from Amazon and we had a really tough time loading the bin file using the Daily Builds but finally got it to load. But there are no channels below Channel 1 and there is a header showing "!!!UNTESTED HARDWARE!!!.

I have attached the Support Data file (.tgz) and here is the Sysinfo:
============================================
  http://localnode:8080/cgi-bin/sysinfo

RB952Ui-5ac2nD Stealth Bug

published by AC0WN on Fri, 02/15/2019 - 13:16
Forums: 
Possible Bugs

My apologies if this has been reported elsewhere.

Unit:  MikroTik hAP ac lite router operating normally as a stand alone tunnel client node using firmware build 614-dbfef25 and operating 13 Host Direct.  POE and USB power OFF, and the radio operating as a 2.4 GHz AP.

Pages

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer