You are here

Home

Possible Bugs

Your search for "22" gave back 150 results.
Results for Forum Topic

hAP AC Lite - Excessive DNS Requests

published by KY6O on Mon, 08/01/2022 - 12:57
Forums: 
Possible Bugs

I am running a MicroTik hAP AC Lite (RB952Ui-5ac2nD-TC-US) with the latest recommended AREDN release on a Ubuntu box. While the node functions, the network monitoring folks where I work are telling me that this box is making over 27k DNS requests to Google's DNS server per hour. Originally I thought it was because I had left the browser up in the "Update Node Status" mode, but now I'm not so sure.  It was also connected to a short (20 mile) tunnel. We are re-flashing the hAP now, just in case I had a bad firmware install.

Possible LQM Bug?

published by KV3T on Wed, 08/31/2022 - 16:20
Forums: 
Possible Bugs
Hey team,
I turned on all of my nodes to upgrade all of them to .8 and noticed something interesting in the LQM on one of the nodes.  It is showing a fellow 5G node on the same channel that has a DTD link twice.  It shows an RF link and a DtD link, and the RF link doesn't show as blocked in LQM.  Screenshot below.

3.22.8.0 factory install on PBE-m5-400

published by N9JIM on Wed, 09/14/2022 - 20:54
Forums: 
Possible Bugs
Just got a new Ubiquiti PBE-m5-400.
tried tftp of aredn-3.22.8.0-ar71xx-generic-ubnt-rocket-m-xw-wquashfs-factory.bin
using windows 10...
tftp would either timeout with no message.  Sometimes long time, sometimes short.

tried aredn-3.22.6.0-ar71xx-generic-ubnt-rocket-m-xw-wquashfs-factory.bin and it loaded immediately.

Jim
N9JIM

 

PB620 Ether Port Not Negotiating down to 10/100 Mpbs after v-3.22.8.0

published by WA7NE on Sat, 10/01/2022 - 18:02
Forums: 
Possible Bugs
Was negotiating okay on v 3.22.1.0.  Decided to upgrade to v 3.22.8.0.  RF is running fine but unable to access PB620 via ethernet at 10/100 Mbps after the upgrade.  Could not access PB620 with either a 10/100 Mpbs hub or PC.  Was able to connect using a laptop with 1Gpbs ethernet adapter.  I plan to downgrade and test.  Will report findings.

Version 13.22.8. Advertised Services

published by KA2FNK on Sun, 09/04/2022 - 16:00
Forums: 
Possible Bugs

After upgrading to 13.22.8.0 from 13.22.6 advertised services after a few hours are being dropped..
 Rebooting  the node supporting those services bring services back  for a few hours. Then they
no longer show up under :Services" again.. 

I have reloaded the 13.22.8 several times with the same results both on a rocket and nanostation.
I did not see anything in the advance configuration setting that would impact services 

Rolling back to 13.22. 6 clears the problem.

new GL.iNet 750 not working with 3.22.8.0

published by ka7ezo on Sun, 08/28/2022 - 21:14
Forums: 
Possible Bugs

loaded 3.22.8.0 on a new GL/iNet 750 and it will not give a gateway address. loaded 3.22.6.0 and it works fine. then update to 8.0 and it works fine then.


noel ka7ezo
 

WebServers Not Available through a tunnel

published by n5hzr on Sun, 10/30/2022 - 15:52
Forums: 
Possible Bugs

Greetings,

Two months ago I upgraded a GL iNet AR 150 router to firmware 3.22.8. It has been running non-stop for two months. This router supports a tunnel server with a half dozen tunnel clients, two radios, and a half dozen client machines with a couple of web servers attached.

GL AR-150 on aredn-3.22.8.0 does not have DNS enabled

published by ZL1AXG on Fri, 10/21/2022 - 21:28
Forums: 
Possible Bugs
I installed AREDN latest stable version (aredn-3.22.8.0) on two new AR-150 nodes and neither had functional DNS (but all other functions were nominal).   I then installed an earlier version (aredn-3.22.6.0) with good results.

I suspect something is messed up with DNS in this release.

Mike ZL1AXG

Connected to node - or not?

published by HB9XCL on Sat, 11/26/2022 - 16:16
Forums: 
Possible Bugs

Dear all
maybe someone can try to explain following strange effect:

"Charts" button functionality in 3.22.12.0

published by W1ZPB on Mon, 12/26/2022 - 11:14
Forums: 
Possible Bugs
Greetings:
      After installing 3.22.12.0, I saw something that I haven't seen with older official releases:  if the node is receiving no signals over RF/cannot establish a link to another node on its assigned channel and channel width  [I can't tell which of these two is the case], the "Charts" button doesn't show up (even though the node can see nodes with the same channel width on other channels in WiFi Scan) and instead it says "no RF links". 

Pages

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer