You are here

Home

Hardware

Your search for "28" gave back 1043 results.
Results for Forum Topic

RTSP String for Trendnet Cam

published by Kf7vol on Sun, 11/29/2020 - 01:01
Forums: 
Cameras
Hello to the group,

I have a nice but older Trendnet IP cam. I have been making good headway getting all the RTSP strings for the other cams I have. This little Trendnet is kicking my but. I have looked on the ISpy site where they have some cheat sheets and the ones I have tried have not worked. The camera model is below.

MikroTik Hap ac lite issues

published by VE7LSE on Wed, 02/03/2021 - 01:20
Forums: 
Network Switches
Been running my Hap for a week or 2 now without any issues with 1 tunnel as a client. I go to activate my tunnel server and get it working then reboot to apply other settings and the hap wont reboot now with the WAN plugged into the hap. It just sits there and does not reboot. I have to take the WAN cable out of the hap then pull power and then re apply power and it boots up without the WAN plugged in..... I don't get it. I have re-flashed the firmware and still does this. Anyone else have this problem? Bad Unit or did something mess this up? 

Thanks

Devan

Replacement Model for the hAP ac lite--- hAP ac lite TC

published by VE7LSE on Tue, 02/02/2021 - 13:12
Forums: 
Network Switches
Sounds like the hAP ac lite TC is the replacement for the hAP AC lite. One of our club members was on a call with mikrotik Canada and they told him this. Same guts but different enclosure anyone else heard this news yet?

Thanks

Devan

Filters

published by N8JJ on Sat, 07/30/2016 - 08:35
Forums: 
Nodes
We have had desense problems on 2 node installations now.  One from a 900 Mhz paging transmitter and one from a 1200 MHZ ATV transmitter.  We purchased some chinese filters that cover the entire 2.4 band and are good enough for channel -2.  It solved the problem for the paging xmtr and hopefully will work for the ATV.  However, it would be ideal if we could get or make a filter for channel -2 that was 10 Mhz wide.

Any suggestions?

JJ

GL.Inet GL-USB150 USB DNS Issue (SOLVED)

published by km6zpo on Thu, 01/21/2021 - 12:01
Forums: 
Nodes

I have a GL-USB150 USB setup to tunnel into my home mesh access point which is connected to the internet and tunneled into the MESH through a remote node.  That all works fine.  But I'm having a DNS issue on the laptop.

Here's the scenario:

New Basebox5 showing !!!! UNTESTED HARDWARE !!!!

published by NH6HI on Tue, 02/16/2021 - 04:19
Forums: 
Nodes

Aloha,
Got a new pair of Basebox5's and tried to load the stable and the nightly build with the same result. !!!! UNTESTED HARDWARE !!!! looks like they fiddled with the boards again. I have attached the support Data for evaluation.

73 & Aloha
Jim NH6HI

NBE-M5-16 support status

published by i8fuc on Sun, 02/21/2021 - 19:54
Forums: 
Nodes
Hi, I am trying to install latest  AREDN sw non such device,  without success ...   in the supported matrix it is a "MAYBE " device...   do anybody be able to setup AREDN on this device up to now ?

Maybe an old SW version could be ..

Thanks for any help

Michele I8FUC

Adaptation for ZoneFlex ZF7762-S

published by n3gwg on Tue, 02/23/2021 - 11:57
Forums: 
Nodes

Forum members,

I have a ZoneFlex ZF7762-S that I'd like to use for AREDN. Now, there was conversation on the OpenWRT forum a while ago about this ZoneFlex device in particularity, but basically other than some basic discussion it went nowhere. However, reading there you can find what was discussed.

Daisy chaining (DtD) nodes and hAP AC Lite

published by N6SAF on Sun, 06/21/2020 - 14:59
Forums: 
Hardware

I recently flashed my hAP AC Lite with the AREDN firmware. My configuration is as follows: hAP (port 5) > NSM5 XW > NBM5. Since the flash to AREDN firmware I can only access the hAP and the NSM, I can no longer access the NBM node. It shows up as a neighbor of and DtD linked to the NSM, but when I click the address link it just times out.

I'm guessing my settings are wrong somewhere. Perhaps I need to disable or change DHCP settings on one, two or all of the nodes? Or do I need to use static addressing and/or NAT?

Unable to flash AREDN FW to RBLHG-5HPnD XL

published by N6SAF on Sat, 11/07/2020 - 21:29
Forums: 
Nodes
I get the below message on the PXE load, and when I try to load the FW the second time permanently I get "Bad Gateway." I've used the AREDN documented method successfully with another RBLHG-5HPnD XL, but for some reason I cannot get this one to work. Thoughts?

node: NOCALL-252-114-178
model: MikroTik RouterBOARD RBLHG-5HPnD

!!!! UNSUPPORTED DEVICE !!!!
boardid: MikroTik RouterBOARD RBLHG-5HPnD
Device has not been tested. Please file a ticket with your experiences.

br-lan C4:AD:34:FD:72:B2
eth0   C4:AD:34:FD:72:B2

Pages

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer