You are here

Home

Hardware

Your search for "28" gave back 1043 results.
Results for Forum Topic

Question about USB Serial Adapter

published by W6SOI on Wed, 04/21/2021 - 20:05
Forums: 
Nodes


TP-Link Archer T3U USB dongle

published by KR6CV on Fri, 04/30/2021 - 23:54
Forums: 
Nodes
Hi,
Forgive if this has been brought up before. Can this USB dongle be adapted to AREDN? It has 2 and 5 GHz freqs and is MIMO enabled.

https://www.tp-link.com/us/home-networking/usb-adapter/archer-t3u/

Thanks in advance,
Stan KR6CV

MikroTik CSS106 / RB260GSP config for AREDN

published by KM4DC on Thu, 07/18/2019 - 07:22
Forums: 
Network Switches
The attached documents my setup for a MikroTik CSS106/RB260GSP switch. This is a 5 port (with optional SFP) managed switch with POE-in on port 1 and POE-out available on ports 2-5. I wrote this up because the switch is quite different from other switches I've used.  The result presented here is still a work in progress, but it seems to work OK. Comments welcomed. I paid about $60 for the switch.

HOWTO: Revert a CPE510 to Pharos

published by kf6iiu on Fri, 04/30/2021 - 16:58
Forums: 
Nodes

I had no problem installing AREDN on a CPE510 V3.20/3.28 (Software says one, sticker on device says newer), but I could not revert to Pharos using the file upload feature in the AREDN web interface. I think this is typical of Pharos devices. 

I tried using use the following dnsmasq command after setting the wired ethernet connection to 192.168.2.1/255.255.255.0:

dnsmasq -i enp2s0 -u root --log-dhcp --bootp-dynamic --dhcp-range=192.168.2.110,192.168.2.120 -d -p0 -K --dhcp-boot=recovery.bin --enable-tftp --tftp-root=/tftp/

Mikrotik SXTsq5 not loading

published by KK4AVI on Thu, 04/22/2021 - 08:30
Forums: 
Hardware
I have a Microtik SXTsq5 (RBSXTsq5HPnD) and I can't get it to load the firmware. I have tried multiple time to load the factory .elf file and have bin unsuccessful. Anyone have an idea or the procedure to load the firmware?

Adding A Node

published by K2PMD on Thu, 05/06/2021 - 09:58
Forums: 
Nodes

So, I am brand new to all of this and am working hard to get Pittsburgh hams to get a MESH going here. Several of my ham friends are buying hardware and working with their clubs. 

I successfully flashed a Mikrotik hAP AC lite yesterday and it is connected to my primary shack computer. I understand this to be my first node.

Rocket M2 Titanium can't reconnect after powering down

published by kc7rjk on Sun, 05/02/2021 - 00:27
Forums: 
Hardware
​Hello Group,
 
I've acquired a NOS RM2 Ti - us. After uploading the current "TI" firmware and going through first boot procedure everything works great connects to the mesh wifi network no problems as expected and no issues rebooting using the GUI button. BUT after powering down the unit it becomes unaccessible via mesh or LAN. Tried uploading the firmware twice with the same result.
 
Regards,
Ross kc7rjk

GL iNet-AR300m16-EXT Flash Problem

published by N4NQY on Mon, 05/10/2021 - 14:10
Forums: 
Nodes

I have the above unit and downloaded the software.   When flashing to AREDN Firmware from stock, using the Update procedures, I get the following error "Failed! ERROR: Incorrect firmware format!"

Tried on two different machines, using Stable and Nightly builds.  Any one have a clue how to proceed??  The model appears to be supported, best I can tell.

jb  N4NQY

GL AR300M16 in nightly builds

published by AE6XE on Sat, 05/18/2019 - 00:57
Forums: 
Nodes
The code to support the GL AR300M16 is in the nightly builds, available from May 18th, 2019.    Summary of specs:

* 2GHz
* comes with or without 2 external antennas models
* 23dBm max xmit power
* 2 ports -  LAN/DtDlink (untagged/vlan 2) and WAN (untagged)
* power is supplied with USB 5v cord (could run for days on readily available battery pack typically used to charge cell phones)
* look for the "gl-ar300m" image
* 3 led lights:   power, booting/booted, established mesh link

UniFi G3 Pro Camera

published by ke7mqf on Sat, 05/15/2021 - 19:24
Forums: 
Cameras
Okay, it looks like I goofed.  I ordered two of these things to place on an AREDN node in Bountiful, UT.  While trying to get them operating (computer networking is not "my thing"), I find that they have to be hooked to a digital recorder, connected to the Internet, and run/operate thru "the cloud". 

Am I missing something?   I really hope I did not spend this money on something that won't work.
Gary KE7MQF

Pages

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer