You are here

Home

Nodes

Your search for "30" gave back 615 results.
Results for Forum Topic

Nanostation M2 Recovery

published by K6BKD on Fri, 02/21/2020 - 13:05
Forums: 
Nodes

I have inherited a NanoStation M2 with AREDN 3.16.x on it and I don't have the root password. So I'm trying to recover it and seemed to not being able to find the correct firmware for it.

M/N: NanoStationM2
FCC ID: SWX-M2N
IC: 6545A-M2N

So is this the non XW version? I've tried the Factory image aredn-3.19.3.0-ubnt-nano-m-xw-factory.bin and it gives a firmware error so I assume it's the wrong one. I don't see a firmware that is not XW. So what do I load on this to reset it so I can get it working again?

Nano

published by Kf7vol on Sat, 02/22/2020 - 10:20
Forums: 
Nodes
Hello Group,

What would be the complications if any if I tried to build a near 360 deg coverage with ubiquity 2.4GHz nano's. Has anyone else tried this and what were you results?

I am trying to get near 360 deg coverage without using a bullet and an omni which I have heard do not yield the best results.

Thank you,

Ubiquiti PowerBeam AC Gen2 Support?

published by W1RFX on Mon, 02/24/2020 - 16:27
Forums: 
Nodes
I've been eyeing this system for a while, but just came upon some cheap hardware to potentially give AREDN a try. I picked up this AC Gen2 PowerBeam for a shamefully low price with the thought that it might be a good candidate for AREDN. Now upon checking out the supported hardware list, I don't see this one listed. Is this one just untested, or is the chipset entirely unsupported? I appreciate any guidance!

MicroTik dish/hAP no longer working over LAN as dtd or wan

published by kk6qms on Sun, 03/08/2020 - 15:54
Forums: 
Nodes

My MicroTik dish is connected to my hAP port 5 w PoE on. I see the dish only via tunnels not dtd as I always have. "KK6QMS-5GHz-dish (tun*1) 5.14"

Same behavior whether I use PoE injector and a switch or plug dish direct to port 5 w PoE ON. I just updated to build 1375 as well- no change. I checked it physically and it is fine- reboots when the hAP reboots, 28dB path to Edom hill which is LOS 8mi away.

From the dish I do see that hAP dtd/wan but LQ 100% and NLQ 0% Any ideas to resolve appreciated. Clifford - KK6QMS

PowerBeam M5 bricked?

published by LA9UI on Mon, 03/09/2020 - 17:51
Forums: 
Nodes
I have one PowerBeam M5 that is not working. It had 3.19.3.0. I tried to upgrade to a nightly version, but it seems that I used a wrong file in the process. I do not get any contact with the M5, but it seems to boot in a normal manner, with front and back LEDs on, and the #2 from back indicate it is communicating. I do not get a DHCP address, and the machine do not answer on 192.168.1.20 or 192.168.1.1. Is there any hope?? I also have one M5 working, I just upgraded to 1375-812c007.

Rack mount options?

published by KD2HKB on Wed, 03/18/2020 - 08:37
Forums: 
Nodes
Hi There,

I was thinking about the local mesh and was wondering if AREDN's MikroTik firmware may run on other devices like the MikroTik RB1100 or rb1200.

M2 Bullet not taking initial setup

published by Kf7vol on Sat, 03/21/2020 - 21:29
Forums: 
Nodes

Good Evening,

I have been fighting a M2 bullet I have. after several try's I was able to get the firmware on the device. I began to celebrate but soon realized I wasn't out of the woods. I have a couple things going on. I have had success flashing other bullets so I don't feel that I am to far of track on this one. Below are the items that I'm running into.

Ubiquiti Air Router HP - How to change networks

published by N3IIG on Wed, 03/25/2020 - 20:32
Forums: 
Nodes

Question 1
My home network ip range is 192.168.x.x
The air router is configured to the 10.xx.xx.xx network range
Not being a network wizard I'm not sure how to make it available on my network like it use to be when the house was setup in the same 10.xx.xx.xx range. 

Attached is an image of the setup page on the Air Router

Question 2

GL-150 Firmware Location

published by AC0WN on Thu, 05/02/2019 - 19:51
Forums: 
Nodes

Hi ...

My apologies if I have missed this somewhere.  I see the listing for the firmware on the Readme file under software, but I can't find the firmware file anywhere.

Can someone please give me a pointer as I have a GL-150 arriving Saturday.  :)

Many thanks,
julie mcgrew
ac0wn
 

Firmware for Nanobridge M3?

published by KR6CV on Sun, 03/29/2020 - 01:52
Forums: 
Nodes

Hi,
I am unsure which firmware to use to update my Nanobridge M3. Can someone direct me to the correct version?

Thanks

Stan KR6CV

Pages

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer