You are here

Home

Hardware

Your search for "28" gave back 1043 results.
Results for Forum Topic

Can’t log in to Ubquiti NanoStation M2 NSM2US after configuring

published by AA8K on Thu, 12/05/2019 - 11:45
Forums: 
Hardware

Logged into my new Ubquity NanoStation M2 version 6.1.7 (XW)
on my Windows 10 Home 1809 desktop.
My home LAN is 192.168.0.x.
I used my second PCI LAN card set to 192.168.1.127.
I found the NanoStation at 192.168.1.20.

I used tftp to load the 3.19.3.0 factory firmware, transfer successful.

I found the NanoStation at 192.168.1.1.
I went to the Basic Radio Setup page and changed my Node Name, Password, Channel, and Power.

When I Save Changes, I can no longer find the NanoStation.

MikroTik Metal52ac

published by DD4SG on Thu, 12/05/2019 - 15:04
Forums: 
Nodes
Hi,
I am new to the Arden topic and I have a question to all who uses Hardware from MikroTik. 

I have a leftover-Device from an other Project. This Device is al MikroTik Metal52AC. It transmitts on 2.4G and 5G and has an waterproof Case with an N-Plug Connector, witch is quite nice for a Node. 

As anyone flashed such a device with the Arden Firmeware and Tested it? I did not find the Device on the List, and I really think that the Company reuses the internal Hardware in different Devices. 

hAP ac lite update fails with "Bad Gateway"

published by K2QA on Sun, 03/31/2019 - 21:58
Forums: 
Nodes
Hello,

Trying to flash​ hAP ac lite - (RB952Ui-5ac2nD-US) with AREDN firmware using Windows 10 instruction video from KK6RAY.

I can TFTP boot from .elf file with tiny PXE.

When I try update using setup/administration to upload the .bin file, wireshark shows lots of packets from Windows to hAP, then hAP returns "Bad Gateway" and resets the TCP connection.

I have tried:
aredn-3.18.9.0-mikrotik-rb-nor-flash-16M-ac-sysupgrade.bin
aredn-3.19.3.0-mikrotik-rb-nor-flash-16M-ac-sysupgrade.bin

I've tried many times.

Mikrotik RB751U

published by EA2BB on Sat, 12/07/2019 - 12:03
Forums: 
Network Switches
Hi 
Some experience with this router model?. I tried to load the .elf and it doesn't support it

3ghz antennas

published by NH6HI on Thu, 12/19/2019 - 17:56
Forums: 
Antennas
Aloha ,
Not sure if these are any good. Happened upon them while looking at coaxial cable. Sure can't beat the price.
https://www.shireeninc.com/osc/3-3-3-8-ghz-mimo-antenna

Mikrotik LDF 5 support

published by AE6XE on Sat, 12/08/2018 - 00:54
Forums: 
Nodes

Announcing availability of the MIkrotik LDF 5 in Nightly Builds from Dec 8, 2018

Called the "Lite Dish Feed" (LDF), this device is intended to mount on a re-purposed satellite dish.  The xmit power of this device is 25dBm for only ~$38, very cost effective.  See the specs here:

https://mikrotik.com/product/rbldf_5nd

"The offset mount is universal at 40mm diameter, and the LDF can easily be placed inside it."

need help setting up Basebox2 (RB912UAG2HPnD)

published by KR6CV on Sat, 12/28/2019 - 18:15
Forums: 
Nodes

Hi,

I have been unable to connect to my new basebox via the browser interface (192.168.88.1).

I have turned off DHCP and assigned my computer 192.168.88.10 and still cannot connect via wifi

Winbox can connect with the node via ethernet but can I reset device settings through this program?

Trying to find out what firmware version I have to see if I can flash or "wait" for an update

Any advice would be welcome!

Stan KR6CV

Using Linux Machine

published by KI7LIK on Tue, 12/31/2019 - 00:23
Forums: 
Nodes
Please point me in the direction to be able to use raspbian to load the factory file to my new nanosation m5.

Thank you.

Beyond 5 GHz

published by w6bi on Wed, 01/01/2020 - 21:26
Forums: 
Nodes
Regardless of the outcome of the pending FCC NPRMs, we in the ham radio networking community need to try to take control of our future.

A bit of brainstorming here (caveat: I'm familar with RF design, but not at microwave):

10 GHz is the next band with enough bandwidth to accomplish the kind of throughput we need to continue to maintain and expand our network.

hAP AC Lite, No Load

published by w8erw on Fri, 01/03/2020 - 20:31
Forums: 
Hardware
Is anyone having an issue with a new Mikrotik hAP AC Lite?  I received two new units recently.  The first one was a piece of cake.  The AREDN firmware loaded and configured nicely.  The second unit, not so pretty good.  I can get through the initial load with PXE.  When I bring it up again to configure and save, it comes back with the factory firmware.  Any thoughts?  I've tried all the tricks I know of.  Again the first one went fine.  Same procedure with the second and it will not retain the AREDN firmware.  I am using the current release of firmware, no nightly builds.  This thing is being

Pages

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer