You are here

Home

Hardware

Your search for "28" gave back 1043 results.
Results for Forum Topic

GL-150 Firmware Location

published by AC0WN on Thu, 05/02/2019 - 19:51
Forums: 
Nodes

Hi ...

My apologies if I have missed this somewhere.  I see the listing for the firmware on the Readme file under software, but I can't find the firmware file anywhere.

Can someone please give me a pointer as I have a GL-150 arriving Saturday.  :)

Many thanks,
julie mcgrew
ac0wn
 

Firmware for Nanobridge M3?

published by KR6CV on Sun, 03/29/2020 - 01:52
Forums: 
Nodes

Hi,
I am unsure which firmware to use to update my Nanobridge M3. Can someone direct me to the correct version?

Thanks

Stan KR6CV

my AREDN Air router got corrupted, keeps rebooting

published by wa2ise on Wed, 03/25/2020 - 17:40
Forums: 
Nodes
I had this AREDN Air router working for a few months, but somehow it got "stupid".  It keeps rebooting every 25 or so seconds, and it never establishes an ethernet connection to my PC.  The computer sees something, then it reports the ethernet cable is disconnected, and this repeats. 

I opened up the Airrouter, to see if maybe there was a bad electroytic cap or such I could fix.  That wasn't it.  I then saw a header on the board "UART" I connected a TTL level serial connection to that and my PC.  For once I guessed correct as to which pin is TX and RX.  Upon powerup I get:

Mesh for home use

published by WB5YDA on Mon, 03/30/2020 - 15:43
Forums: 
Nodes
I want to setup a mesh for my home. I was familiar with it back my Hamnet days, but now want to setup with Ubiquiti devices. Can you reccomend  inexpensive devices to do that with?

Neatgear GS108E V3

published by KE8IJV on Fri, 03/27/2020 - 10:17
Forums: 
Network Switches

i recently purchased the NetGear GS108E V3 and set it up as a 6 LAN 1 Node 1 Wan.  I used the set up that was on the Forum for a GS105E  but made it fit the GS108E.  It is not working.  Does anyone have the setup for this that works?  Thank you

AirRouterHP Firmware Upgrade

published by VA3QT on Tue, 03/31/2020 - 16:08
Forums: 
Nodes

Just successfully upgraded an AirRouter node to Firmware Ver 3.20.3...  and verified that it's working with my AirRouter HP node.  However, when I try to update the HP node (and selecting the Ver 3.20...Susupgrade.bin file) the Upload box is greyed out and inoperative.  Can anyone advise how to correct this?

73,

Ian VA3QT

OpenWRT router to act like a Netgear smart switch on AREDN node

published by wa2ise on Fri, 03/01/2019 - 14:50
Forums: 
Network Switches

aim is to use an OpenWRT router to support a Bullet or an M900

tftp of 1439-cdd1f8e into

published by K5edj on Sun, 04/05/2020 - 14:15
Forums: 
Nodes

Bullet m2hp xw with 1439-cdd1f8e w/ errors on save.

I performed a tftp to my bullet to aredn-1439-cdd1f8e-ath79-ubnt_bullet-m-xw-factory.bin
Each time I try to save my settings on this bullet it returns errors.
After a reboot, the values are saved except the new password is not updated.
 

BULLET BM2 FIRMWARE DOWNGRADE

published by VA3QT on Fri, 04/03/2020 - 17:40
Forums: 
Nodes

I've an "old" Bullet BM2-HP  that I converted some 4 years ago.  It's since been in storage for quite awhile.  I connected it to a Win7 laptop, logged into "localnode ..." and up came the GUI as expected.  Trusting neophyte that I am, and having successfully updated a pair of AirRouters, I tried to update the Bullet.  It failed and gave every appearance of being locked up.  Of course I failed to write down the
AREDN firmware version number I had put on it.

BaseBox 2.4GHz

published by WA3LAB on Sun, 04/05/2020 - 20:26
Forums: 
Nodes

Is anyone using the BaseBox 2.4GHz radio, and if so, does the AREDN software allow the 30 dbm selection to run a full power? 

Glenn
WA3LAB

Pages

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer