You are here

Home

Hardware

Your search for "28" gave back 1043 results.
Results for Forum Topic

Switch for DtD with independent remote control of PoE on all ports

published by AC0WN on Mon, 05/04/2020 - 13:12
Forums: 
Network Switches

Hello All ...

I would very much appreciate your views on which switch would be my best choice to make Device to Device connections that can be remotely controlled across the AREDN network to apply PoE to its ports individually.  I would like to have at least 5 ports on the switch.

"Untested Hardware" Nanostation M2 and 3.20.3.0

published by ng1p on Thu, 05/07/2020 - 08:00
Forums: 
Hardware
I got a Nanostation M2 on eBay and tried to load 3.20.2.0 and got the ​"Untested Hardware" banner. I then loaded 3.19.3.0 and it worked fine.

I have attached the support data file for this Nanostation M2 (XM) version. I'd like to get this device on the latest firmware if possible.

Thank you Bill NG1P

 

Mikrotik devices and 5Mhz bandwidth?

published by ng1p on Mon, 05/11/2020 - 22:01
Forums: 
Hardware
I have heard reports the some Mikrotik devices only work at 10 and 20Mhz bandwidth (not 5Mhz)? Is this true for all Mikrotik devices that support the AREDN firmware? I have a local ham trying to connect to the mesh using the 27dB gain Mikrotik dish and it's not working. 

thank you Bill NG1P

 

Ubiquity Rocket M2

published by kf7ebx on Mon, 03/09/2020 - 18:22
Forums: 
Nodes

I have a Rocket M2, brand new that was donated to me. I am trying to flash it to Aredn using my Mac Terminal on TFTP. When I send the file I get the following back:

Error Code 514: Firmware check failed.

When I log into the ubiquity firmware it confirms it is a M2 XM, which is the firmware I downloaded. This leaves me questioning if I need to downgrade it before I can TFTP the aredn factory file to it? 

Status settings in AIR OS are:
version: 5.6.11 (XM)
Device Model: Rocket M2
Any thoughts would be helpful. 

AMO-2G13 Not Omnidirectional

published by w8erd on Sun, 05/17/2020 - 08:04
Forums: 
Antennas
Ubiquiti advertises their AMO-2G13 antenna as being omnidirectional, but if you look at the horizontal pattern on their web site, it is 5 dB down on the
"sides".  How can one determine the directions of maximum radiation by looking at the antenna?  I wrote to Ubiquiti and asked this question but they did not reply.

Bob W8ERD

NonaStation M5 Firmware

published by k6dlc on Fri, 05/15/2020 - 22:40
Forums: 
Nodes
   I am having issues on saving after trying to change my password

Configuration NOT saved!
  • invalid Mesh RF channel
  • Invalid country
  • invalid LAN netmask
  • invalid WAN DNS 1
  • invalid ntp server firmware version
    configuration system time uptime
    load average free space
    3.20.3.0
    not set
    Thu Feb 27 2020
    21:10:44 UTC
    4 min
    0.02, 0.10, 0.05

Mikrotik RBLHG-5nD - !!!! UNTESTED HARDWARE !!!!

published by KM6KDZ on Sat, 05/16/2020 - 18:22
Forums: 
Hardware

Having trouble installing AREDN on a MikroTik RouterBOARD RBLHG-5nD running RouterOS v6.44.6.

Tried with both current and nightly builds. On Windows, using PXE Server, carefully following Ray KK6RAY's YouTube video. Have previously done two HAP 5s and hoped this process would be about the same. It's a little different, and maybe that's where I've gone wrong, or perhaps the hardware isn't supported?

See below and any suggestions or info would be appreciated.
Thank you, Chris KM6KDZ
  The progress goes:

Rocket self-contradictory

published by w8erd on Fri, 05/22/2020 - 09:28
Forums: 
Nodes
I have a rocket M2 XM on my tower.  When I went to update the firmware, a line appeared that said:
hardware type ubnt (nanostation-m
This is clearly wrong, and the free memory of 46284KB confirms it is not a nanostation.
It would not accept a rocket update.
It did accept a nanostation update to 3.20.3.0, and it seems to work.

I tried other updates, including another to 3.20.3.0
They all fail and say: 
Firmware cannot be updated
Upload file is not recognized
Failed to restart all services
Please reboot this node

Is it 'RBLHG-2nD-XL' or 'RBLHG-2HPnD-XL'?

published by K9CQB on Wed, 02/13/2019 - 22:32
Forums: 
Nodes

I really wanted to find the best 2.4GHz high-gain point-to-point dish to close some links at some sites that already have 5GHz equipment on them. But I still want to spread the love of a 2.4GHz AREDN node in the general direction of that community that we are shooting over, making it easy for them to get on the mesh network. So one of the options on the supported list was the RBLHG-2HPnD-XL. I scrubbed the internet for them, but could find them. So I thought it was a typo and bought the RBLHG-2nD-XL. And then I found out the real deal:

MikroTik hAP change VLAN

published by iz5fsa on Mon, 05/25/2020 - 08:39
Forums: 
Nodes
Is there a way to set another eth port as D2D?
Change it from VLAN1 to VLAN2, I suppose...
--
73 de Leo IZ5FSA
 

Pages

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer