You are here

Home

Hardware

Your search for "28" gave back 1043 results.
Results for Forum Topic

Point to point link passing internet

published by KB6UMY on Thu, 06/13/2019 - 19:08
Forums: 
Hardware
Hi Everyone,
             I have 4 Ubiquity M5 XM Rocket transceivers. Myself and and another network tech have spent over 40 hours racking our brain on how to setup a link from my office to a mountain top through a switch and have a mesh node with internet access. We have been successful at getting two of the nodes to link together, but internet has been imposable to get through the nodes.
       In short I'm looking for settings to use two units as a PTP link through a POE switch and broadcast the node with available internet. Any help would be much appreciated.

ProCurve 1700-24 switch

published by LA9UI on Sun, 07/07/2019 - 09:05
Forums: 
Network Switches
I have tried to use a ProCurve 1700-24 switch with the setup from Understanding VLAN's by K5DLQ. I have 2 NanoStation loco M2 and 2 NanoBridge M5. It seems that I cannot control all the necessary parameters. I use 5 ports on the switch. DtD between a NanoBridge M5 and NanoStation loco M2 is working, but the RF connection between the two NanoBridge M5 is only intermittent.The RF connection between the NanoStations is solid. Can the ProCurve be used successfully with AREDN?

Hans-Petter  LA9UI

Migrate from HSMM to AREDN on Bullet M2 high power

published by NH6HI on Sun, 07/07/2019 - 19:16
Forums: 
Nodes
Aloha,
I was given a M2Bullet High Power FCC ID SWX-M2B and have searched the archives and found this thread ( https://www.arednmesh.org/content/bbhn-aredn ) Maybe there's another thread I missed.
They mentioned BBHN 3.1.0 but the one I have has 3.0.0. How do I migrate it over to AREDN without bricking it?  The plan is for a portable node for now. I know it's not the latest and greatest but it's free and I hate to see it wasted.
Jim NH6HI

LAN connection constantly dropping and coming up

published by KE0RSX on Sun, 07/07/2019 - 20:40
Forums: 
Hardware
Hi, everyone,

I'm not entirely sure which subforum to put this in so here goes. I'm currently working with the TP-LInk WBS210 and have it flashed with the firmware. It doesn't matter if I connect LAN1 or the LAN0 from the PoE adapter to my network, I see it constantly going up and down. On my DHCP server, I see it constantly sending DHCPOffers to the device, but nothing indicating an acceptance. Also, this happens when I have a TP-LInk CPE210 plugged in in place of the WBS210.

hap-less

published by KM4DC on Sat, 07/06/2019 - 07:21
Forums: 
Nodes
Greetings,
My Mikrotiik ac lite (RB952Ui-5ac2nD-US) was working great for months.
It was running aredn-960-d8f9320-mikrotik-rb-nor-flash-16M-ac-sysupgrade firmware.
But, I turned it on this morning at there are no port lights, no Ethernet.
I did a reset and still no Ethernet ports. (Hold reset, apply power, wait for light)
I'm guessing a hardware failure but wanted to see if anyone had an idea no how to get it working.

And, thinking ahead - if it is toast; is there a better replacement?

Unifi Switch to Unifi Switch over SFP - Help getting DTD Linking Through Non-Mesh Network

published by AK4FA on Mon, 07/15/2019 - 16:17
Forums: 
Network Switches

I have two Unifi Switch 8's connected over SFP, one in my shop, the other in the house. 
I have my mesh gateway unit connected at the house where the internet comes in, it is an ARHP.
I have an M2 Loco in the shop where I connect to a few other mesh devices via RF.
There is no RF connection between the house and the shop.

I'd like to be able to DTD the ARHP in the house with the M2 Loco in the shop via the Unifi 8 switches, which are not on AREDN.

GL-150 Tunnel Client/Server

published by n9ms on Mon, 05/13/2019 - 09:08
Forums: 
Nodes

My GL-150 works great EXCEPT I am unable to install either the tunnel client or server. I get a message: Package Installation failed. Is this a limitation of this device?

New to AREDN

published by LA9UI on Fri, 06/07/2019 - 09:29
Forums: 
Nodes
Hi!

I am trying to set up a mesh in Northern Norway. I have 2 Nanobridge M5. Installed Aredn 3.19.3 on both, OK. Was setting up with default values. Seems to be working, but the two radios (running barefoot) does not see each other. They are a few meters apart, with low power. Can anyone tell what I am doing wrong?

Hans-Petter  LA9UI

Mikrotik LHG HP5 w/nightly build issues

published by K6BAT on Wed, 07/17/2019 - 01:03
Forums: 
Nodes

I was able to flash a new LHG HP5 radio with the nightly build (7/3/19), and the hardware is recognized correctly (I see this model was added to the code after the 3.19.3 release). I am able to link to Pleasants on 174. However, I cannot seem to pass traffic outside my node. First I thought it was just DNS not working, but if I ssh into the node I cannot ping anything outside my network, even though I seem to have a "good" wireless connection. I'll attach a supportdata file if that helps. Any suggestions? Or should I just be patient and wait for a release that covers this model?

Smallest, full-power AREDN node: modified PowerBeam M2

published by K9CQB on Thu, 08/01/2019 - 16:01
Forums: 
Hardware
I needed a small, full-powered, AREDN node to mount on a tiny drone aircraft and some small drone boats that run up and down a river. I've also been searching for a small, but full-featured AREDN node for a man-wearable system. So after looking around for a good host device that I could remove from the case and buying and cutting up many different nodes I found the PowerBeam M2 (PBE-M2-400). Here's what I found:

Pages

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer