You are here

Home

Nodes

Your search for "30" gave back 615 results.
Results for Forum Topic

LHG Dish cannot load firmware

published by wa0vus on Sat, 01/09/2021 - 12:40
Forums: 
Nodes
I and another ham each have a pair of dish nodes.  LHG XL 2.it says on the label.  We have been unable to get a firmware to load except once.  
We use PXE server and that has worked for other Microtic hAP we have.up and meshing.

1.Setup laptop with static 192.168.88.20 and turn off wireless. runs thru switch.
2.start PXE and it sees the ip .of 20.
3. Set rb.elf file to load on PXE
4. Press dish reset and powerup.
5. wait 10 minutes.
6. Set laptop for dhcp.
Unable to find the dish on 192.168.1.1 or 192.168.88.1.

hAP AC Lite No Load

published by w8erw on Fri, 01/03/2020 - 20:28
Forums: 
Nodes
Is anyone having an issue with a new Mikrotik hAP AC Lite?  I received two new units recently.  The first one was a piece of cake.  The AREDN firmware loaded and configured nicely.  The second unit, not so pretty good.  I can get through the initial load with PXE.  When I bring it up again to configure and save, it comes back with the factory firmware.  Any thoughts?  I've tried all the tricks I know of.  Again the first one went fine.  Same procedure with the second and it will not retain the AREDN firmware.  I am using the current release of firmware, no nightly builds.  This thing is being

POE Not Working on Mikrotik HAP AC

published by KD0VWH on Wed, 01/20/2021 - 18:07
Forums: 
Nodes

I am running a Mikrotik HAP AC to a TP-LINK CPE210 running firmware 38-3faf42c on the Mikrotik and firmware 3.20.3.1 on the CPE210.  When I initially configured my setup at my kitchen table using 2 ft cat6 cables everything worked great.  I was able to communicate to the Mikrotik and it saw the node as a neighbor through port 5 on the Mikrotik (yes, I have POE passthrough turned on).

bricked m5 nanostation

published by N8CAV on Sun, 01/03/2021 - 15:37
Forums: 
Nodes
I have a 5g nano xm that had been working with the 3.19.x.x software. When I tried updating to 3.20.3.1 using UI the lights on the node all flashed and then only the green power light on the left side remained on. I tried to tftp it and it does not respond at all. I cannot make it do anything.
 

PBE-M5-400 not responding.

published by kp4osp on Mon, 01/25/2021 - 21:08
Forums: 
Nodes
Hello,

NanoStation M5 no IP after Flash (solved)

published by DD4SG on Sat, 01/23/2021 - 17:29
Forums: 
Nodes

Hi Folks,

I startet with Aredn once again. (last Year I  configured some Loco M5 Stations. 

Now I have 3 Loco M5 running with an Grandstream Telefon and its is working fine. 

I have recently purchachsed an NanoStation M5 to get an 4th Node running. Unfortunatelty the Flashing did not work.

I  checked first the Firmware on den Os and it says XM.v6.2.0 So I decided to take the 3.20.3.1...-m-factory.bin. I used the Main Lan connection to flash the device. 

LiteBeamM5 LBE-M5-23-US will not flash Aredn Firmware

published by AA3JC on Sat, 01/30/2021 - 13:58
Forums: 
Nodes
Just received 3 LiteBeamM5 Model: LBE-M5-23-US that will not flash Aredn Firmware.  All three give me the same error trying to update the firmware to Factory  aredn-3.20.3.1-ar71xx-ubnt-lbe-m5-factory.bin  "Wrong Firmware version is uploaded. Please upload the correct version and try again".  I also tried the Sysupgrade version, and also the Nightly version,  aredn-84-99305c5-ar71xx-ubnt-lbe-m5-sysupgrade.bin also with the same error on all three.  

LHG LX 5HP Trouble with factory file

published by DL6MCO on Fri, 01/29/2021 - 14:44
Forums: 
Nodes

Hi specialists,
I'm not able to flash an LHG LX 5HP with the rb.elf file.
As soon as the download starts, I get following output:

rolf@rolf-Inspiron-7720:~$ sudo dnsmasq -i enp3s0 --dhcp-range=192.168.1.100,192.168.1.200 --dhcp-boot=rb.elf --enable-tftp --tftp-root=/tftp/ -d -u rolf -p0 -K --log-dhcp --bootp-dynamic
dnsmasq: gestartet, Version 2.79, DNS abgeschaltet
dnsmasq: Übersetzungsoptionen: IPv6 GNU-getopt DBus i18n IDN DHCP DHCPv6 Lua TFTP conntrack ipset auth nettlehash DNSSEC loop-detect inotify

Filters

published by N8JJ on Sat, 07/30/2016 - 08:35
Forums: 
Nodes
We have had desense problems on 2 node installations now.  One from a 900 Mhz paging transmitter and one from a 1200 MHZ ATV transmitter.  We purchased some chinese filters that cover the entire 2.4 band and are good enough for channel -2.  It solved the problem for the paging xmtr and hopefully will work for the ATV.  However, it would be ideal if we could get or make a filter for channel -2 that was 10 Mhz wide.

Any suggestions?

JJ

GL.Inet GL-USB150 USB DNS Issue (SOLVED)

published by km6zpo on Thu, 01/21/2021 - 12:01
Forums: 
Nodes

I have a GL-USB150 USB setup to tunnel into my home mesh access point which is connected to the internet and tunneled into the MESH through a remote node.  That all works fine.  But I'm having a DNS issue on the laptop.

Here's the scenario:

Pages

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer