You are here

Home

Hardware

Your search for "28" gave back 1102 results.
Results for Forum Topic

External HD on Mikrotek HAP

published by NI0P on Fri, 02/24/2023 - 16:26
Forums: 
Nodes
Does anyone have the instruction for using an external HD attached to the Mikrotek HAP. Want to use it for file storage.

Node it up and running on the latest firmware.


Thanks
NI0P
Brian
 

Mikrotik RB2011

published by ke5lgg on Sun, 07/31/2022 - 15:09
Forums: 
Network Switches

Is there an AREDN firmware for the Mikrotik RB2011 router? I did not see one under software.
Thank you

 

Nanostation M2 (XM) stuck at 3.19.3.0 - Upgrading "bricks" it

published by W5CWT on Tue, 12/20/2022 - 01:51
Forums: 
Nodes

Unit works, but can't seem to upgrade one of my M2s past 3.19.3.0

I have two (seemingly) identical Nanostation M2 (XM) units (as well as other units). One M2 upgraded fine to 3.20.XX and then recently to 3.22.XX without problems. The other one will not. When I upgrade via the Aredn GUI, it reboots and eventually gets to state with the power LED on and a very slow red flash only (left strength LED). Noting works at that point. I must use TFTP to revert back to AirOS 5.6.16, then I can load the 3.19.3.0 factory bin.

Ubiquiti Rocket M5 availability

published by NM7B on Wed, 10/26/2022 - 10:55
Forums: 
Nodes
I'm hunting down a couple more Rocket M5s to complete my mesh system build out.  I have noticed that Rocket M5s have gotten much harder to find, and I have seen one comment that they have been discontinued.  

Can anyone confirm if the Rocket M5 is still in production or end-of-life?  Is there a plan or intent to support another version of the Ubiquiti Rocket so there's continuity with the installed base of Ubiquiti Rocket M5-compatible antennas?  

Thank you, and my complements for the excellent firmware work!

Collier
NM7B
 

Support for integrated MikroTik sector nodes mANTBox 19s or other sectors?

published by W1ZPB on Tue, 03/14/2023 - 09:30
Forums: 
Nodes
Greetings:
     AREDN-supported Ubiquity Rocket M5 radios are becoming harder and to find, making it harder and harder to use them in Ubiquity sectors, which are designed to hold and cover the node against the back of the antenna.

Ubiquiti Rocket M5 Titanium w/ GPS

published by N0MRZ on Mon, 03/21/2022 - 22:58
Forums: 
Nodes

I recently replaced the Rocket M2 in my mobile rover (truck) with an M5 Titanium as we are converting our network to 5 GHz. This node has the availability for GPS and has an external GPS antenna which I stuck on the roof of the truck. I access the node with an Apple iPad. (works quite well!)

My question is this, will the AREDN software utilize this feature in it's firmware and use that information to update my lat/lon location of my mobile unit? Will the firmware be able to access the GPS information for anything? I know Ubiquiti makes a standard M5 that also has GPS.

Ethernet Switch

published by AD9BU on Mon, 04/10/2023 - 12:26
Forums: 
Network Switches
Hello all,

I currently have a Mikrotik hAP ac lite set up as my QTH node and currently have it tunneled into a friends node, my question is I'm currently running out of ports on the back of my router and was wondering if I could buy a netgear ethernet switch and hook it up like that or if i would have to get another router and do another node?

Thanks
James
AD9BU

GL.iNet Collie (GL-X300B) 4G LTE Wireless Gateway

published by KG7GTC on Tue, 04/11/2023 - 13:08
Forums: 
Nodes
Greetings everyone,

Has anyone had any experience with the GL.iNet Collie (GL-X300B-GPS or GL-X300B-BLE)?  I just purchased one, and was curious if AREDN would run directly on it. I've got the GPS version, and plan on using it on the road with T-Mobile.

Sadly, their 4G/5G version (GL-X300 Spitz AX) isn't out yet. For my upcoming road trip this week, I'll use it as designed, and just plug one of my AREDN GL750's or hAP ac lites into it.

Need help with port forwarding on Zone Minder

published by AD9BU on Mon, 04/17/2023 - 23:05
Forums: 
Cameras
Ive got the application installed but i cant find out how to get or change the port number any help please

CPE710 channels wrong

published by WA3LAB on Sat, 02/18/2023 - 13:55
Forums: 
Nodes
I just flashed the latest nightly build for the CPE710 and the channel selection has an issue. Originally I tested the CPE710 with my shop unit on channel 180 which is a NanoStaion M5 and it connected OK.  I then changed the  channels on both nodes to 146.  The units would not connect.  I did a WIFI scan on the CPE710, and it shows itself at channel 149, and likewise a scan on the NanoStation indicates  the CPE710 is channel 149.  Coincidentally, the default channel after the initial programming was 149.  

Pages

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer