You are here

Home

Hardware

Your search for "28" gave back 1102 results.
Results for Forum Topic

hAP AC Lite slow to boot

published by KN6NK on Sat, 12/17/2022 - 21:08
Forums: 
Nodes
I just flashed a new hAP AC Lite (RB952Ui-5ac2nD) with 3.22.12.0 but it takes an exceptionally long time to boot up, more than 5 minutes.  Is this expected behavior for this device, or should it boot faster than that?  I also have a RBLHG-5nD with 3.22.12.0 that boots up in less than a minute.
I've attached the support file for the hAP AC Lite (though dmesg looks like it only takes ~30sec from kernel start to link up, I'm not sure what's happening before that...is there a UART console available on these?

Backup node settings

published by DL1MDR on Fri, 12/16/2022 - 16:20
Forums: 
Nodes

I want to backup/export the settings on an AREDN-Node to be able to restore/import them in case the node has to be set up new. How can I do this?

Thanks for any help, Markus.

Latest OpenWRT Nightly won't Sysupgrade

published by KE6GYD on Mon, 12/26/2022 - 20:30
Forums: 
Hardware
Tried two times to sysupgrade my Ubnt Powerbeam PBE-M5-400 using the following file.
aredn-2038-6fba065-ath79-ubnt_powerbeam-m5-xw-sysupgrade.bin

It went to the "Do not remove power during the update" page.  Eventually, both times it reverted back to 3.22.12.0.  No packages were installed and it was rebooted just prior to upgrading.  Device was connected direct to my local computer thru a dumb switch. 

Latest OpenWRT 22.03.2 Nightly WILL upgrade PowerBeam

published by KE6GYD on Tue, 12/27/2022 - 13:33
Forums: 
Hardware
Latest Nightly as of Dec 27 was successful in SysUpdating two of my PowerBeam PBE-m5-400's.  The previous two would not update.

One was done locally direct to the computer via a dumb switch, the other was on my roof via a managed switch.  That device was dtd'd to my local node through the switch. 

Trouble loading firmware - did I buy the wrong unit?

published by VE7NZ on Wed, 12/07/2022 - 00:13
Forums: 
Network Switches

I am getting errors (bad block or bad packet - i forget exactly now what it said) in the UI on PXE Server when trying to flash the factory firmware to the Microtik unit i bought.  I bought this one and am wondering if it is actually not compatible... https://solimedia.net/product/hap-ac-lite-tower/.  Part Number RB952Ui-5ac2nD-TC.  If someone could let me know, or what the errors are about, I would appreciate it. The unit connects to PXE but the firmware install does not successfully complete. Thx, 73, Adrian VE7NZ 

Challenges mounting a USB Drive on Mikrotik HAP

published by KI6GOA on Mon, 01/02/2023 - 20:36
Forums: 
Network Switches

Okay, I've been beating my head against a problem for a few days now and I've finally reached the point where I'm going to ask the group for some help.

AC Equipment

published by W7BJH on Wed, 12/28/2022 - 02:04
Forums: 
Nodes
Any chance there is some firmware under development for the AC 2.4 and 5 GHz Ubiquiti equipment?  I've got an NBE-5AC-16 on-hand that I'd like to put to work and there is actually some AC gear in stock.

Cheers, 

BJ - W7BJH

Nightly for NanoBridge 5G25?

published by KE6GYD on Tue, 01/10/2023 - 22:51
Forums: 
Nodes
I know the nightlys' now are using OpenWRT release, version 22.03.2 and that some older 32MB Ram devices like the NanoBridge 5G25 are being sunsetted.
Has the sun set on these devices yet?  Or does this OpenWRT release, version 22.03.2 nightly still work on these devices but has not been tested?

If the nightly will still work, I'd like to try it on my NanoBridge, but don't know what nightly file to use.  If sunsetted, then I'll just continue to use the last stable release.

Thanks
Bob
KE6GYD
 

Acquisition of IP Address

published by K6BZZ on Fri, 01/13/2023 - 13:06
Forums: 
Cameras
I am trying to attach an IP Cam to my AREDN Nano node. I have read many instructions and watched many videos, but have never been able to get the node to recognize the camera IP address. How do you do that?  Is it supposed to be automatic when attaching the camera? I know the camera IP address but find nowhere to input it AREDN setup page.
Any help appreciated.

'73 de Dick K6BZZ



 

TP-Link CPE610v2 problem

published by LU4EOU on Tue, 01/10/2023 - 10:41
Forums: 
Nodes

Hello.
I have 1 tplink node cpe610-v2 updated until 3.22.12.0 all ok, updated with NB 2024 ok, then 2065 ok, then to 2074 ok, 2081 ok, to 2089 ok, to 2096 ok, to 2103 ok, then I could not update more, try with 2110, with 2124 and with 2131 and the same error.

Firmware CANNOT be updated
firmware file is not valid: platform check image failed

Any ideas that will help me?

Thanks
Mario, LU4EOU

Attached file

Pages

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer