You are here

Home

Hardware

Your search for "28" gave back 1043 results.
Results for Forum Topic

Newbie queston on Netgear GS105eV2 set up

published by WM6Q on Fri, 02/07/2020 - 17:06
Forums: 
Network Switches
I'm sure this is basic, but I am lost on all the networking set up. I have a Mikrotik routerboard tunneling to the AREDN mesh through a hardwired internet connection. I also have two RF nodes: an 18inch dish and a Nanostation. I would like to be able to access each of these three nodes from my computer. I have all three nodes plus the computer plugged into the Netgear GS105eV2 switch. I am only able to access the routerboard. How do I select what I can connect to?

Thanks!!

Bob WM6Q

Nano station m5 bricked on 3.20

published by ki5edt on Fri, 04/03/2020 - 16:37
Forums: 
Nodes

I have a Nanostation m5 that ran AREDN 3.19 fine for nearly 1 year  . So the new software came out last week and I did upgrades to 3 of my 10 various branded nodes and the nanostation m5 NS5N and now it won't boot.
It sits there there with the power light stays solid and the 2 lan ports and the 2nd and 3rd signal lights flash quickly and go out at the same time.
 Any ideas?

Duplicate IP Addresses

published by AF6FB on Fri, 03/22/2019 - 20:53
Forums: 
Nodes
Hello,
I have two nodes that have the same LAN address. One is a Ubiquity NanoStation Loco and the other is a Mikrotik hAP.

I have flushed browser history, DNS, powered down each device and only had one connected at a time. How can I give one of them a different address? I see that I can change the WiFi IP address, I'm a little afraid to as it might conflict with someone else. The LAN addresses I can't change.

I need some direction. Here are some screen shots...

Odd problem installing on NanoBridge M5

published by kg7bz on Sat, 06/13/2020 - 22:37
Forums: 
Hardware

I have run across some NanoBridge M5 units that I can't install the firmware on. I can't install any version, recent or old. These have AirOS v6.2.0 (XM), when I do the tftp transfer, it almost completes and then I get the error "Firmware Check Failed". I'm just having this problem with these 4 nodes, I have no problem with others. Are there some unusual ones out there that have this problem?

August KG7BZ

Meraki MR16

published by KF6ODE on Sun, 05/23/2021 - 16:22
Forums: 
Nodes

GitHub indicates that an image has been built for the Meraki MR16, however I have been unable thus far to track it down.

Does it in fact exist?

Rocket M5 not working after an upgrade from V. 3.18.9.0 to V. 3.19.3.0

published by AC2OG on Tue, 06/25/2019 - 06:24
Forums: 
Nodes

Hello,
my rocket M5 was working nicely with AREDN firmware 3.18.3.0, but it got blocked after trying to upgrade to 3.19.3.0. The upgrade session was going on for 20 min., so I decide to disconnect the PC. When I tried the new connection I got the initial page as a newly flashed device, but the frequency windows in the basic setup disappeared, as well as the RF IP address. Please see the attached docx.
Is there a way to recover the device?

Tnx and 73 de Leo AC2OG / I3RKE

MikroTik SXTsq Lite2 Case

published by ke3kq on Thu, 12/02/2021 - 13:30
Forums: 
Hardware
Hi,
I have an SXTsq Lite2 that I have been unable to reset the password.  I cannot get back to NOCALL, SETUP etc to reset the PW.   BTW it seems that the PW was changed by a password manager on a MS Windows PC used to access the Setup page afterwhich the PW was changed.  Weird, I know.  It boots up fine just don't know what the new password might be so can't really manage it.

Anyway, the 15 second reset switch powerup process will not bring back the NOCALL screen for me.  Seems the reset switch may not be working for some reason - sigh.

PowerBeam M5 works

published by KK4IB on Sun, 04/03/2022 - 09:42
Forums: 
Network Switches
WE set up a new Ubiquiti PowerBeam M5 300 ... it programmed with AREDN MESH no problems. It was connected it to a Mikrotik HAP-AC-Lite 5th port (PoE). It set up correctly, all parameters. The network found it. Then it connected to a stand-alone Ubiquiti Bullet M5 (once the frequencies were set to the same), and the network is tunneled.

We approve the PowerBeam M5, ... KK4IB and KC4JIR, Middle GA network [www.ga-aredn.lumasis.net; ga-aredn-users@groups.io].

Rocket M2 XM

published by w8erw on Tue, 04/05/2022 - 21:55
Forums: 
Nodes
I have unable to apply the latest nightly release to a Rocket M2 XM.  Many tries and no luck. 
It looks like it might be working, seems to reboot once and then returns to the administration screen unchanged.
Initially it was working on a much earlier release, 405 I believe it was.  I had success in getting to take the current stable
release however.  But it will not update with the currently nightly. I stopped counting the number of attempts.  I did use the drop down

mANTBox 2

published by w8erw on Fri, 04/15/2022 - 17:53
Forums: 
Nodes
I recently picked two new mANTBox devices.  Neither will load the rb.elf file.  Each time I try I get a message stating it is not the correct file?Are there additional procedures?  What ever am I doing wrong.    Thanks,

Jim
W8ERW
 

Pages

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer