You are here

Home

Hardware

Your search for "28" gave back 1102 results.
Results for Forum Topic

LEDs on LHG XL 2

published by N7BTW on Thu, 01/13/2022 - 02:02
Forums: 
Nodes

Are the LEDs expected to work right on the RBLHG-2nD-XL at this time? I just set mine up with a nightly build less than 2 weeks ago, and I only get the power and 3rd and 4th rssi LEDs lit (solid). I even played around with /etc/config/system (replicating the configuration hypothesized in /etc/board.json) until I got rssileds to run. I can see the brightness values being updated in /sys/class/leds/rb:green:rssi*, but the actual LEDs don't change. This is with an active mesh connection to another node.

GL-Inet AR150 and MikroTik hAP AC lite

published by AC2OG on Fri, 12/24/2021 - 10:25
Forums: 
Nodes
AR150 and hAP both flashed with firmware version 3.21.4.0 don't mesh at 5 MHz bandwidth. At 10MHz bandwidth yes. 
Is there a way to make them mesh at 5 MHz Bandwidth ? 
Merry Christmas and Happy New Year

 

Adding additional hardware Support LDF-5acD

published by K0dyy on Wed, 09/22/2021 - 20:27
Forums: 
Nodes

I made a mistake and ordered a Lite Dish Feed 5 (LDF-5acD) not supported,  as opposed to a Lite Dish Feed 5 (LDF-5nD) which is supported. 
I have been told that the 5acD is on the list  for support, I was just wondering when  the 5acD support may become available.
 Thanks
 

No WiFi Scan result

published by iz5fsa on Wed, 01/26/2022 - 08:09
Forums: 
Nodes

Upgrading to latest 3.22.1.0 my 2 nodes:
  1) Mikrotik hAPac
  2) GLiNet AR750
don't have results at wifi scan.
I need linking each other via 2G wifi mesh link.

Any other have same troubles?

73 de Leo IZ5FSA

PBE400 almost 525 ft away

published by AH6LE on Sun, 09/12/2021 - 11:35
Forums: 
Antennas
I'm doing a new installation of a Ubiquiti PBE400 that will require a cable run of almost 525 feet.

Now, I know I'll need a POE Extender for this but my question is if the 12 watt POE injector that comes with the Powerbeam is adequate to the task or do I need something different? I suspect the 12 watt one isn't.

My plans are to use Ubiquiti Carrier Class Tough Cable for the run but I'm open to less expensive alternatives (but only if it doesn't compromise reliability and ruggedness).

AirRouter HP

published by wb0gag on Tue, 03/09/2021 - 07:58
Forums: 
Nodes
I could not get the nodes (I have 3) to accept the latest firmware, so I tried aredn-3.19.3.0-ubnt-airrouter-factory.bin.  That worked easily.  I will try to update later to see if the new firmware can be uploaded under AREDN firmware control.

Inexpensive 2.4GHz Antennas

published by KV3T on Wed, 02/02/2022 - 10:24
Forums: 
Antennas
Hey all,

Rocket M5 EU

published by K0JNR on Sun, 02/06/2022 - 14:43
Forums: 
Hardware
I ordered 3 Rocket M5 from Amazon, however they are EU models.   If I flash them, will they work in the US?

usb ethernet with pi zero in hap usb port

published by k0cdf on Sun, 01/16/2022 - 07:37
Forums: 
Hardware
hello

I have a pi zero w with a board soldered to it that combines the usb power and data ports into a usb A coming out of the side.

I want to use it with my portable hap ac lite.

I have made it so if i plug it into my laptop it shows up as a usb network card.
if I turn on network sharing I can access the pi

is there a way to make it so it can do this with the hap as well?

since I have an m2 loco on port 5 of the hap I turned off the hap rf mesh and set the hotspot to 2.4 and the pi is connecting that way now.

GL.Inet AR300 dTD question

published by KE0RSX on Mon, 02/07/2022 - 14:43
Forums: 
Nodes
If I remember correctly, you can set these to use both Ethernet ports for LAN/mesh. Would it give you two dTd ports then?

Thanks and have a great day. :)
Patrick.

Pages

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer