You are here

Home

Nodes

Your search for "30" gave back 615 results.
Results for Forum Topic

Nanostation Second Port

published by K7DXS on Wed, 03/02/2016 - 15:19
Forums: 
Nodes
Are we planning on ever supporting the second port on a Nanostation? It would be quite useful to have.

Installing patch

published by k3la on Sat, 04/23/2016 - 11:21
Forums: 
Nodes
I am trying to reconfigure a bullet m5 to aredn. I have ver 3.1. Of bbrn installed. In following instructions I tried install the patch to install the keep settings. When I download the patch file it is a compressed file and an error message appears if I try to use the file as is. What am I missing? Barney K3LA

Actual spread of Rocket 120 sector antenna

published by kc8rgo on Thu, 04/28/2016 - 09:00
Forums: 
Nodes
I have a situation where an area I would like to cover with the Rocket M2 w/120 degree sector antenna is only 2 miles or less away from the antenna.  Can I effectively cover this at about 10 degrees out side of the 120 degree spread advertised for this antenna?

I would just try it, but it is a tower climb.

Thanks - Kc8RGO

From BBHN to AREDN

published by w7rej on Tue, 07/28/2015 - 22:43
Forums: 
Nodes

What steps are needed to flash Ubiquiti nodes that are already running BBHN? Are they flashed as factory or as sysupgrade? I searched the forums and the site and can't find anything the specifically addresses this.

NSM3 availability?

published by w6bi on Thu, 05/12/2016 - 00:17
Forums: 
Nodes

Flytec Computers indicates they're currently out of the NSM3 ("Unavailable").
Any suggestions on how to acquire a pair?

Thanks.

Planned hardware support mikrotik?

published by UA6EM on Wed, 05/18/2016 - 10:01
Forums: 
Nodes
Planned hardware support mikrotik?
http://www.mikrotik.com
 

TPLINK CPE510 Hardware not supported!

published by M0OLI on Wed, 03/09/2016 - 07:45
Forums: 
Nodes

Hi 

Seem to be having a Hardware issue, CPE210 worked just fine, however I received the TPLINK CPE510 v1.1 on firmware 1.3.0 this morning and I get the message 'The Hardware is not supported' when I try to upload AREDN firmware via the Firmware upload section.

Any ideas on the problem here, thanks in advance.

Hardware is TPLINK CPE v1.1 and the installed firmware was 1.3.0
ATTEMPTED: Tried to roll back firmware to v1.2.1 still will not take AREDN firmware 'The Hardware is not supported.'

Flash failure on NS M5

published by WE7AA on Tue, 05/31/2016 - 12:00
Forums: 
Nodes

So I bought a brand new NanoStation M5 and has the board and firmware XW 5.6xxx. I flashed it over to XW.v5.5.10-u2.28005.150723.1358 and all went well. Then flashed it to AREDN-3.16.1.0-ubnt-nano-m-xw-squashfs-factory. This also went ok, but now I can't get into the web ui to set it up. Yes I did change the computer over to receive IP automatically, using the right port on NanoStation.

What I did with my old HSMM Linksys node since I upgraded

published by wa2ise on Wed, 05/25/2016 - 14:56
Forums: 
Nodes

Now that I have Ubiquity nodes up and running, I took my old Linksys's out of service.  As they can't do channel -2.  Okay, what to do with the Linksys's?  Tried to convert one (a version 2 WRT54G)  to become OpenWRT, no go.  DDwrt?  no go.  Okay, back to Linksys firmware, still no go...   Probably a step I don't know about smiley  Looked, but didn't find anything.

Got an Airrouter to test the RX/TX of my Bullet and to access nodes

published by wa2ise on Tue, 05/17/2016 - 15:14
Forums: 
Nodes

Found a way to access nodes via tunnel and over the air on channel -2.  Using a flashed AirRouter.  I kept the tunnel on the Bullet, so other hams can connect directly to the nodes on the tunnel. 

Pages

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer