You are here

Home

Hardware

Your search for "28" gave back 1043 results.
Results for Forum Topic

NSM3 availability?

published by w6bi on Thu, 05/12/2016 - 00:17
Forums: 
Nodes

Flytec Computers indicates they're currently out of the NSM3 ("Unavailable").
Any suggestions on how to acquire a pair?

Thanks.

Planned hardware support mikrotik?

published by UA6EM on Wed, 05/18/2016 - 10:01
Forums: 
Nodes
Planned hardware support mikrotik?
http://www.mikrotik.com
 

TPLINK CPE510 Hardware not supported!

published by M0OLI on Wed, 03/09/2016 - 07:45
Forums: 
Nodes

Hi 

Seem to be having a Hardware issue, CPE210 worked just fine, however I received the TPLINK CPE510 v1.1 on firmware 1.3.0 this morning and I get the message 'The Hardware is not supported' when I try to upload AREDN firmware via the Firmware upload section.

Any ideas on the problem here, thanks in advance.

Hardware is TPLINK CPE v1.1 and the installed firmware was 1.3.0
ATTEMPTED: Tried to roll back firmware to v1.2.1 still will not take AREDN firmware 'The Hardware is not supported.'

Netgear GS108Ev3 as vlan separator and switch

published by wa2ise on Sat, 05/21/2016 - 23:20
Forums: 
Network Switches
As per the instructions at http://www.aredn.org/content/configuring-netgear-gs105e-switch-lanwan-ports I configured a GS108Ev3 as a combo Ubiquity node LAN/WAN splitter and also as a switch on the WAN side.  Where I located this box I needed a few ethernet ports switched off the input WAN (connects to my main switch and router and in turn the cable modem) which would feed a couple computers not involved with AREDN.  One port is for the Bullet, 2 ports are the Bullet's LAN, and the rest are WANs.  The WANs

Failure to obtain DHCP lease from Rocket M3

published by WB6YOK on Mon, 05/23/2016 - 16:09
Forums: 
Hardware
I have a brand new, out of the box, Rocket M3, that I am unable to obtain a DHCP lease from.

1. I have tried two different laptops.
     a. Windows 7, newly staged.
     b. Xubuntu 14.04
     c. Both laptops can obtain a lease from my local
 network.
2. I have tried three different power supplies.

3. I have tried several different cables, tested of course.

4. I even tried another factory firmware flashed Ubiquity device. Same issue.

I've done dozen's of these devices in the AREDN space and this stumps me.

While Shopping at MicroCenter ....

published by N2MH on Sat, 05/28/2016 - 13:57
Forums: 
Hardware



While shopping at MicroCenter, some hardware caught my eye. An "AMPED" brand with a piece of hardware that looks suspiciously like a Nano Station.

Don't know if this is any good and probably don't want to use it considering its source. But, I thought it was interesting.

73, Mark, N2MH

Flash failure on NS M5

published by WE7AA on Tue, 05/31/2016 - 12:00
Forums: 
Nodes

So I bought a brand new NanoStation M5 and has the board and firmware XW 5.6xxx. I flashed it over to XW.v5.5.10-u2.28005.150723.1358 and all went well. Then flashed it to AREDN-3.16.1.0-ubnt-nano-m-xw-squashfs-factory. This also went ok, but now I can't get into the web ui to set it up. Yes I did change the computer over to receive IP automatically, using the right port on NanoStation.

What I did with my old HSMM Linksys node since I upgraded

published by wa2ise on Wed, 05/25/2016 - 14:56
Forums: 
Nodes

Now that I have Ubiquity nodes up and running, I took my old Linksys's out of service.  As they can't do channel -2.  Okay, what to do with the Linksys's?  Tried to convert one (a version 2 WRT54G)  to become OpenWRT, no go.  DDwrt?  no go.  Okay, back to Linksys firmware, still no go...   Probably a step I don't know about smiley  Looked, but didn't find anything.

Access WLAN without switch

published by KD7MG on Tue, 05/31/2016 - 20:47
Forums: 
Network Switches

The motherboard in my Windows 7 PC came equipped with dual Realtek gigabit NIC's and I read in another forum where these can be configured to handle VLAN tagging. (Some Intel and Broadcom chipsets can also handle tagged frames.) The configuration consisted of upgrading to the latest Realtek (NOT Microsoft) driver, then installing the Realtek Ethernet Diagnostic tool. The tool comes in 2 flavors, one for Windows XP thru 8.1, and another written just for Windows 10.

Got an Airrouter to test the RX/TX of my Bullet and to access nodes

published by wa2ise on Tue, 05/17/2016 - 15:14
Forums: 
Nodes

Found a way to access nodes via tunnel and over the air on channel -2.  Using a flashed AirRouter.  I kept the tunnel on the Bullet, so other hams can connect directly to the nodes on the tunnel. 

Pages

Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer