Have three nanobridge units. All three converted successfully. One with xm v5.3 has expected freq./chan range from 5650 to 5925.
The other two were xm v5.2 Say:" untested hardware report experience". They have a freq range choice from 5180 to 5485 They work as expected as a two station mesh network.
Looking at sysinfo both the v5.3 and v5.2 have identical reports. Can the two v5.2 be brought up to the freq range of the v5.3? Do I need to "report" this some place else? Thanks for any help.
You are here
nanobridge - frequency range
Thu, 11/30/2017 - 13:58
#1
nanobridge - frequency range
Theme by Danetsoft and Danang Probo Sayekti inspired by Maksimer
Attach below here where it says "Support File Attachment".
73,
W6ABJ
Here's a link of how to capture the information we'd need:
https://www.aredn.org/comment/5071#comment-5071
Joe AE6XE
Since device was converted ubnt address/login did not work - telent to device address did work
cat instruction did not find filee
dmesg follows:
WARNING: passwords are sent unencrypted.
W5OXC-12 login: root
Password:
BusyBox v1.22.1 (2017-02-26 10:52:23 PST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_____ ______ _____ _ _
/\ | __ \| ____| __ \| \ | |TM
/ \ | |__) | |__ | | | | \| |
/ /\ \ | _ /| __| | | | | . ` |
/ ____ \| | \ \| |____| |__| | |\ |
/_/ \_\_| \_\______|_____/|_| \_|
AMATEUR RADIO EMERGENCY DATA NETWORK
Release 3.16.1.0
-----------------------------------------------
BASED ON OpenWRT BARRIER BREAKER r42549
-----------------------------------------------
* 1 Battery Connect all devices
* 2 POE injectors Upgrade firmware to AREDN
* 3 cat5 cables Setup with your callsign
* 1 UBNT NanoStation Point the Antenna
* 1 ipCam Welcome to the Mesh!
-----------------------------------------------
root@W5OXC-12:~# dmesg
[ 0.000000] Linux version 3.10.49 (cmlara@CMLARA-OpenWRT) (gcc version 4.8.3
(OpenWrt/Linaro GCC 4.8-2014.04 r42549) ) #3 Mon Feb 27 22:27:40 PST 2017
[ 0.000000] MyLoader: sysp=04317d70, boardp=712eab20, parts=7fffffff
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR7240 rev 2
[ 0.000000] Clocks: CPU:390.000MHz, DDR:390.000MHz, AHB:195.000MHz, Ref:5.000
MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
[ 0.000000] On node 0 totalpages: 8192
[ 0.000000] free_area_init_node: node 0, pgdat 80334b60, node_mem_map 8100000
0
[ 0.000000] Normal zone: 64 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 8192 pages, LIFO batch:0
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32
bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag
es: 8128
[ 0.000000] Kernel command line: board=UBNT-BM console=ttyS0,115200 mtdparts
=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,7552k(firmware),256k(cfg)ro,64k(EEPROM)
ro rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 28588k/32768k available (2369k kernel code, 4180k reserve
d, 621k data, 272k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.060000] Calibrating delay loop... 259.27 BogoMIPS (lpj=1296384)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 512
[ 0.080000] NET: Registered protocol family 16
[ 0.090000] MIPS: machine is Ubiquiti Bullet M
[ 0.090000] registering PCI controller with io_map_base unset
[ 0.300000] bio: create slab <bio-0> at 0
[ 0.310000] PCI host bridge to bus 0000:00
[ 0.310000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[ 0.320000] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.320000] pci_bus 0000:00: No busn resource found for root bus, will use [b
us 00-ff]
[ 0.330000] pci 0000:00:00.0: [168c:002a] type 00 class 0x028000
[ 0.330000] pci 0000:00:00.0: fixup device configuration
[ 0.330000] pci 0000:00:00.0: reg 10: [mem 0x00000000-0x0000ffff 64bit]
[ 0.330000] pci 0000:00:00.0: supports D1
[ 0.330000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.330000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.330000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bi
t]
[ 0.340000] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.340000] Switching to clocksource MIPS
[ 0.350000] NET: Registered protocol family 2
[ 0.350000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.360000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.370000] TCP: Hash tables configured (established 512 bind 512)
[ 0.370000] TCP: reno registered
[ 0.380000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.380000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.390000] NET: Registered protocol family 1
[ 0.390000] PCI: CLS 0 bytes, default 32
[ 0.410000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.420000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT
Y) (c) 2001-2006 Red Hat, Inc.
[ 0.430000] msgmni has been set to 55
[ 0.440000] io scheduler noop registered
[ 0.440000] io scheduler deadline registered (default)
[ 0.450000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.480000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 0.490000] console [ttyS0] enabled, bootconsole disabled
[ 0.500000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[ 0.510000] m25p80 spi0.0: found mx25l6405d, expected m25p80
[ 0.510000] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
[ 0.520000] 5 cmdlinepart partitions found on MTD device spi0.0
[ 0.530000] Creating 5 MTD partitions on "spi0.0":
[ 0.530000] 0x000000000000-0x000000040000 : "u-boot"
[ 0.540000] 0x000000040000-0x000000050000 : "u-boot-env"
[ 0.540000] 0x000000050000-0x0000007b0000 : "firmware"
[ 0.560000] 2 uimage-fw partitions found on MTD device firmware
[ 0.570000] 0x000000050000-0x00000015e5a9 : "kernel"
[ 0.570000] mtd: partition "kernel" must either start or end on erase block b
oundary or be smaller than an erase block -- forcing read-only
[ 0.580000] 0x00000015e5a9-0x0000007b0000 : "rootfs"
[ 0.590000] mtd: partition "rootfs" must either start or end on erase block b
oundary or be smaller than an erase block -- forcing read-only
[ 0.600000] mtd: device 4 (rootfs) set to be root filesystem
[ 0.610000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.620000] 0x000000500000-0x0000007b0000 : "rootfs_data"
[ 0.620000] 0x0000007b0000-0x0000007f0000 : "cfg"
[ 0.630000] 0x0000007f0000-0x000000800000 : "EEPROM"
[ 0.740000] libphy: ag71xx_mdio: probed
[ 1.310000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:04 [uid=004dd0
41, driver=Generic PHY]
[ 1.320000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 1.330000] TCP: cubic registered
[ 1.330000] NET: Registered protocol family 17
[ 1.330000] Bridge firewalling registered
[ 1.340000] 8021q: 802.1Q VLAN Support v1.8
[ 1.350000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 1.360000] Freeing unused kernel memory: 272K (8034c000 - 80390000)
[ 4.230000] usbcore: registered new interface driver usbfs
[ 4.230000] usbcore: registered new interface driver hub
[ 4.240000] usbcore: registered new device driver usb
[ 4.250000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.260000] ehci-platform: EHCI generic platform driver
[ 4.270000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.280000] uhci_hcd: USB Universal Host Controller Interface driver
[ 7.320000] eth0: link up (100Mbps/Full duplex)
[ 8.380000] jffs2: notice: (315) jffs2_build_xattr_subsystem: complete buildi
ng xattr subsystem, 11 of xdatum (0 unchecked, 10 orphan) and 171 of xref (0 dea
d, 154 orphan) found.
[ 8.430000] eth0: link down
[ 10.900000] NET: Registered protocol family 10
[ 10.920000] nf_conntrack version 0.5.0 (450 buckets, 1800 max)
[ 10.930000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 10.950000] Loading modules backported from Linux version master-2014-05-22-0
-gf2032ea
[ 10.960000] Backport generated by backports.git backports-20140320-37-g5c33da
0
[ 10.970000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 11.040000] xt_time: kernel timezone is -0000
[ 11.080000] cfg80211: Calling CRDA to update world regulatory domain
[ 11.080000] cfg80211: World regulatory domain updated:
[ 11.090000] cfg80211: DFS Master region: unset
[ 11.090000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gai
n, max_eirp), (dfs_cac_time)
[ 11.100000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 m
Bm), (N/A)
[ 11.110000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 m
Bm), (N/A)
[ 11.120000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 m
Bm), (N/A)
[ 11.130000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000
mBm), (N/A)
[ 11.130000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000
mBm), (0 s)
[ 11.140000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000
mBm), (0 s)
[ 11.150000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 m
Bm), (N/A)
[ 11.160000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0
mBm), (N/A)
[ 11.240000] PPP generic driver version 2.4.2
[ 11.250000] NET: Registered protocol family 24
[ 11.300000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 11.320000] ath: EEPROM regdomain: 0x0
[ 11.320000] ath: EEPROM indicates default country code should be used
[ 11.320000] ath: doing EEPROM country->regdmn map search
[ 11.320000] ath: country maps to regdmn code: 0x3a
[ 11.320000] ath: Country alpha2 being used: US
[ 11.320000] ath: Regpair used: 0x3a
[ 11.350000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 11.400000] cfg80211: Calling CRDA for country: US
[ 11.410000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb0000000, irq=40
[ 11.430000] cfg80211: Regulatory domain changed to country: US
[ 11.430000] cfg80211: DFS Master region: FCC
[ 11.440000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gai
n, max_eirp), (dfs_cac_time)
[ 11.450000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 m
Bm), (N/A)
[ 11.450000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 m
Bm), (N/A)
[ 11.460000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 m
Bm), (0 s)
[ 11.470000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 m
Bm), (N/A)
[ 11.480000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 40
00 mBm), (N/A)
[ 22.870000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 22.910000] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[ 22.940000] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[ 23.150000] eth0: link up (100Mbps/Full duplex)
[ 23.150000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 23.630000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[ 23.630000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[ 24.690000] cfg80211: Calling CRDA for country: HX
[ 24.690000] cfg80211: Regulatory domain changed to country: HX
[ 24.700000] cfg80211: DFS Master region: unset
[ 24.700000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gai
n, max_eirp), (dfs_cac_time)
[ 24.710000] cfg80211: (2300000 KHz - 2600000 KHz @ 40000 KHz), (N/A, 4000 m
Bm), (N/A)
[ 24.720000] cfg80211: (5170000 KHz - 6500000 KHz @ 40000 KHz), (N/A, 4000 m
Bm), (N/A)
[ 26.880000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 29.040000] wlan0: Trigger new scan to find an IBSS to join
[ 33.040000] wlan0: Trigger new scan to find an IBSS to join
[ 35.040000] wlan0: Creating new IBSS network, BSSID 0e:d8:8c:a5:bf:99
[ 35.060000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
root@W5OXC-12:~# cat /etc/board.info
cat: can't open '/etc/board.info': No such file or directory
root@W5OXC-12:~#
Joe AE6XE
Two of them flashed to AREDN 3.16.1.1 just fine and they are usable. However, one of them comes up with the banner of "Untested Hardware". Instead of channels, this one shows frequencies from 5.180 to 5.485 GHz.
What can I do about this one?
Gary AC7R
http://bloodhound.aredn.org/products/AREDN/changeset/69937359c34f89c8c1e...
Joe AE6XE
My file does not have a section for 0xe235. The section for the NBM5 is at 0xe2b5. That section already shows the rfband set to '5800ubntus'. So I do not have anything to change.
So I don't think changing this file is the fix for my issue. Anything else to try?
Gary AC7R
'0xe235' => {
'name' => 'NanoBridge M5',
'comment' => 'NanoBridge M5 in testing',
'supported' => '1',
'maxpower' => '22',
'pwroffset' => '1',
'usechains' => 1,
'rfband' => '5800ubntus',
},
Joe
Now I can go work on two other nodes that I am having problems with. But they are a different issue, so I should open a new topic.
Gary AC7R